Etsy is no longer supporting older versions of your web browser in order to ensure that user data remains secure. Please update to the latest version.
Take full advantage of our site features by enabling JavaScript.
(1,000+ relevant results)
Etsy is no longer supporting older versions of your web browser in order to ensure that user data remains secure. Please update to the latest version.
Take full advantage of our site features by enabling JavaScript.
(1,000+ relevant results)
Contents
1 Get More Switch
Solutions for Nintendo Switch dock complaints range from elegant and simple to somewhat more complex and time consuming. If you see small scratches on your screen added by the dock, then one simple and elegant solution is to make a dock sock.
However, you may be looking to completely change your dock and restore it to your liking. With the advent of home 3D printing, this type of fabrication has become easier than ever. 3D printing repositories like thingiverse.com are amazing. Some change small aspects of the dock, and some redo everything together. Some of my favorite designs fall into the latter category and solve the problem of scratches and sizing at the same time. Designed by Thingiverse user, DylanWave is a beautiful thing.
Many of these designs require you to gut your original Switch dock in order to reconfigure the electronics for your new one. Luckily, docking is not a very complicated business and you can get it up and running in less than half an hour.
Here's how to take your Switch apart to turn it into something more of your liking.
As always proceed with caution when disassembling. The moment you pick up a screwdriver you void your warranty .
To disassemble the Switch dock, you will need a small Philips screwdriver and one small 3-blade screwdriver. You can pick up a tri-fold plate individually, or if you don't have a good set of screwdrivers, you can pick one up at Amazon for all your future repair needs.
With your dock facing down, open the rear door.
Use your tri-blade screwdriver to remove the eight screws from the back.
Carefully lift up the rear panel.
There are two clips to the left of the board. Gently pull them to the left to release the circuit board.
Using a spudger or your fingers, carefully lift the ribbon cable retaining clip.
From the bottom side of the PCB, carefully pull out the wiring harness to the LED.
Now you can put down the board.
Now use a Phillips screwdriver to remove the nine screws inside the case.
Carefully lift the inner casing.
To remove the switch port, use a small Phillips screwdriver to remove the four screws securing it from the bottom.
It's so easy! You are now ready to fit your parts into a much smaller, much less scratchy 3D case!
Did you make or buy a custom Switch dock? Turn off the sound in the comments below!
Rate this article!
USB C Display Hub
13 IN 1 HUB, USB C Dual DP Docking Station (USB3.
0*3+RJ45+SD+TF+HDMI+USB-C DATA*3+USB-C PD+DP*2K USB-C cable)
11 in 1 USB C Hub with HDMI
● Gigabit Ethernet, 3x USB 3.0 ports with data transfer rates up to 5Gbps, 3.5mm audio and a micro SD/TF card reader slot where you can connect a keyboard, USB driver or headset to device C.
● 4K High Definition HDMI Output: One HDMI output. 4K@30Hz Single VGA: 1920*1080.
11 in 1 HDMI to USB C Adapter
11in1 Multiport Dock with USB C PD / USB 3.0 / HDMI Max 4K UHD 3840*2160@30Hz / VGA 1080p 2k@60Hz / AUDIO / SD / TF Neutral Color gray + black cable.
USB C to USB C Hub
HDMI 4K @ 30Hz, VGA Port, Wireless Charger, SD/TF Card Reader, 3x USB 3.0, 4x USB 2.0, 87W PD Type C Charging Port ( charging only), 3.5 mm audio jack and gigabit ethernet.
8 in 1 USB C Hub & 3 USB 3.0 Ports
USB C Hub comes with HDMI (4K @ 30Hz), VGA (1080p), RJ45 Gigabit Ethernet, 3x USB 3.0 ports up to 5Gbps, 3.
5mm audio and Micro SD/TF card reader.
11 in 1 USB C Media Hub
Dual HDMI 4K, VGA 1080p, Gigabit Ethernet, Audio, USB C PD, SD&TF Card Reader, 3x USB 3.0 and 1x USB 2.0 for Metal Ergonomic.
Best 16 Port USB C Hub for Macbook
Designed with 16 ports including 3x USB Type-A 3.0, 3x USB Type-A 2.0, 2x USB Type-C 3.1, Ethernet, HDMI, VGA, USB Type-A input C, SD / TF / CF card reader and audio input / output.
4 in 1 USB C HUB Data Hub
USB3.0 to USB3.0*1 plus USB2.0*3
1. USB3.0: 5Gbps, 1 USB 3.0 port for data synchronization.
2.USB2.0 :Super Speed((480Mbps)
3.Neutral Color: Gray
4.Material: Aluminum Alloy Shell
USB C HUB with 2 HDMI Ports
12 IN 1 HUB USB C Dock (USB3.0*3+RJ45+SD+TF+HDMI*2+USB-C DATA*2+USB-C PD+DP to USB-C cable )
9 in 1 USB 3.0 Hub
The firmware of the USB interface chip is its various basic functions used to perform read and write operations on the chip.
