How to reset jeep tire pressure sensor


Reset Tire Pressure Light

If a flashing tire pressure light has you distracted while driving around Green Bay or if your tire pressure monitoring system (or TPMS) light is permanently on even after refilling your tires with air, let the experts here at Vande Hey Brantmeier guide you through the process of how to reset your tire pressure light! Want us to take care of it for you? Not a problem! Bring your vehicle to our Chrysler, Dodge, Jeep, Ram service center in Chilton any time!

Schedule Service

Contact Us


Resetting Your Tire Pressure Light

In most cases, your TMPS light should turn off after you're inflated your tires with the proper amount of air (usually recommended PSI inflation figures are found in your vehicle's owner's manual. Recommended PSI ranges are also often found on your tire's sidewall. If in doubt, go with the owner's manual recommendations. If your TPMS light remains on, there are a couple of options you can take to rectify the situation and turn it off:

  • Drive your vehicle for 10+ minutes at 50+mph. This should cause your TPMS light to reset the next time you turn on the vehicle.
  • Turn your car off if it's running. Next, turn the key to the “On” position, but don't start the vehicle. After that, hold the TPMS reset button (usually found under the steering wheel) until the tire pressure light blinks three times. Release the button.
  • Start the vehicle and turn it off. Wait 20 minutes for the TPMS system sensors to refresh.
  • Inflate all your vehicle's tires to 3 PSI more than the recommended pressure. Next, deflate them completely. Be sure to include the spare tire, as it may have a sensor as well.
  • Once your tires are deflated, reinflate them to the recommended tire pressure.
  • With the vehicle turned off, disconnect the positive battery cable with a wrench.
  • Start your vehicle and honk the horn for roughly three seconds. This should discharge any power still stored in the vehicle.
  • Reconnect the battery.
  • The above steps should reset your TPMS light and sensors!

What Does a Flashing Tire Pressure Light Mean?

Sometimes, tire pressure monitoring sensors have a battery that requires periodic replacement. If and when this battery begins to get old enough, it could trigger the light to flash. Sometimes, a flashing tire pressure light is also indicative of an issue with one or more TPMS sensors. Either way, if you find that your TPMS light flashes, it's best to schedule service at Vande Hey Brantmeier near Appleton today!

Our Service Center is Here to Help with Your TPMS Issues!

Whether the above steps have failed to help you reset your tire pressure light, or whether you'd just like a professional mechanic to look over your car for fear of messing up expensive sensors or electrical equipment, if you need additional assistance, we're happy to provide it here at the Vande Hey Brantmeier service center near Manitowoc. Our expert Chrysler, Dodge, Jeep, Ram service technicians have the know-how needed to fix your TPMS issues and reset a TPMS light that's on or flashing. They can also provide you information about your vehicle's maintenance schedule. Contact us today to schedule service or with additional service-related questions!


How to Reset Your Tire Pressure Light

Skip to main content

Hide Show

Sell/Trade Us Your Car | Click Here To Learn More

Your tire pressure light provides a critical reminder to restore the pressure in your vehicle's tires when it gets low. You should only attempt to reset the light after first addressing the tire pressure in every tire. Once your tires are at the appropriate pressure, the light may go off on its own. If it doesn't go off right away, driving at 50 mph for about 10 minutes should help the tire pressure sensor reset.

If the tire pressure light is still on, there are a few more tricks you can try:

  • Turn the car key to "on" but don't start the vehicle. Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off within 20 minutes.
  • Disconnect the positive battery cable while the vehicle is off. Turn the car on and press the horn for three seconds to discharge the remaining power. When you reconnect the battery the tire pressure light should be off.
  • Overinflate all the tires (including the spare) with 3 PSI, then deflate them completely. Re-inflate the tires to help reset the light.
  • Bring your vehicle to our service center for professional assistance.

IS TPMS the Same as Tire Pressure Light?

Image via Unsplash by introspectivedsgn.

 TPMS stands for Tire Pressure Monitoring System. The tire pressure light is one component of this electronic system, providing a visual alert when your tire pressure is low. The TPMS monitors tire pressure using either an indirect or direct method.

An indirect TPMS measures the rate of revolution for each wheel. If a wheel starts spinning faster than anticipated, the system signals to your vehicle's computer that something is amiss with the tire rotation, and your tire pressure light comes on. You must manually reset the monitor in an indirect TPMS system.

A direct TPMS uses pressure monitoring sensors in each tire to monitor tire pressure exactly. This is a more accurate alternative to an indirect TPMS system. The batteries inside these sensors will last for about 10 years. Direct TPMS systems reset automatically after tire inflation or rotation. You do need to have these sensors resynchronized when you get new tires, which requires a special tool.

Can Cold Weather Cause Your Tire Pressure Light to Go On?

Yes, cold weather will affect the air pressure in your tires. Your tires lose one or two pounds per square inch (PSI) for every 10 degrees that the temperature drops. Cold air condenses while warm air expands. Therefore, the colder air in your tires will take up less space in lower temperatures.

You may find that your TPMS light is only illuminated for a short time in the morning on particularly cold days. After about 20 minutes of driving, the air will often warm up and expand, restoring proper pressure in your tires. If the light stays on after 20 minutes on the road, you should add air to your tires as needed to restore the proper pressure. Low tire pressure is hazardous for your vehicle regardless of the cause.

Why Is My Tire Pressure Monitor Light On When My Tires Are Fine?

When the tire pressure monitor light is on, the first thing you should do is check the pressure in each of your tires, including the spare. Check the manufacturer's recommendation to determine the appropriate pressure for each tire. This is typically between 30 and 35 PSI but may vary. You should measure tire pressure when the tires are cold, which means they have not been driven in the last three hours.

To check the pressure, simply unscrew the valve cap and insert a tire gauge into the valve stem. The gauge will provide a clear reading. Replace the valve cap when you're finished. If your tires are all at the appropriate pressure, there's a malfunction with your TPMS. Bring your vehicle to an authorized dealership service center to diagnose and resolve the issue.

Is it OK to Drive With My Tire Pressure Monitor Light On?

If the tire pressure monitor light is on, you should check your tire pressure as soon as possible. Low tire pressure creates a serious hazard on the road. According to the National Highway Traffic Safety Administration, 738 people died in tire-related crashes in 2017. When tire pressure is low, the tire has more contact with the road. This may cause the tire to overheat, leading to tread separation, excessive tire wear, or a blowout.

Low tire pressure also wreaks havoc on your fuel efficiency. You can save up to 11 cents per gallon simply by keeping your tires properly inflated. You'll also save money on tire replacements with adequate inflation. Keeping your tires properly inflated can add 4,700 miles to the tire's average lifespan.

The tire pressure monitor light gives you valuable information and should not be ignored.

Do I Need to Replace My TPMS When I Get New Tires?

You do not necessarily need to have your TPMS sensors replaced with new tires, but this is a good time to check them and make sure they're still in good condition. If you have an indirect TPMS system, your mechanic will need to manually reset the sensors after changing your tires. If you have a direct TPMS system, no additional maintenance is required to reset the system.

A new TPMS system will typically last for about 10 years before the batteries run out. If you have an older vehicle, you may need new sensors every five or six years. Your mechanic can advise you on the best time to replace TPMS sensors for your vehicle. When new sensors are installed, the system must relearn the location of each tire, which requires a detailed series of technical procedures. You should leave this task to a professional. 

If you need tire service for your Toyota, come to Kings Toyota for prompt, reliable service. Our highly-trained technicians are equipped to assist with any type of tire issue, whether you need new tires or have a malfunctioning tire pressure sensor light. Make your appointment today.

Make an Inquiry

First Name

Last Name

Contact Me by

EmailPhone

Reset tire pressure signal for Jeep Cherokee

DIY

Frequently asked questions about cars and motorcycles
  1. by car
  2. :
  3. Jeep
  4. :
  5. Cherokee
  6. : Reset tire pressure signal on Jeep Cherokee

Jeep Cherokee - Video Lesson

Model: Jeep Cherokee MK 5, KL - Years 2013-2022
Part: Instrument Cluster
Operation: Reset Tire Pressure Alarm on Jeep Cherokee

The low tire pressure light on your Jeep came on, but you checked and the tire is not flat? Have you checked the pressure in each tire with a pressure gauge, but found no deviations? Great, so the sensor gives an incorrect alarm and you can safely reset it. Press and hold the reset button (located under the steering wheel) until the low pressure light flashes three times, then release the button. Start the engine and let it run for twenty minutes for the computer to calibrate each sensor. Turn off the car and turn it back on to make sure the alarm is gone.

Posted on 23 October 2021 by ScegliAuto


Peugeot 3008 remote battery replacement

To replace the Peugeot 3008 key/remote battery, take a small screwdriver and insert it to lever into the cap with the Peugeot logo. Once the cover has been removed you will gain access to the battery compartment, again using the same screwdriver, lever up to remove the battery. Determine the type of battery (C2032) and replace it, paying attention to the position, i.e. positive pole up. Place the new battery in the provided slot. Move the cover, trying to attach it correctly by pressing with your fingers.

Watch the video!

by ScegliAuto


more videos Posted on 28 October 2022 by

ScegliAuto
  • How to disassemble the power window motor Peugeot 106
    Posted on 28 October 2022 by ScegliAuto
  • How to change the oil in a Fiat Panda 9 engine0040
    Posted on 27 October 2022 by ScegliAuto
  • How to disassemble the Mercedes C-class remote key
    Posted on 26 October 2022 by ScegliAuto
  • How to disassemble mirror Golf 7
    Posted on 25 October 2022 by ScegliAuto
  • How we disassemble the instrument cluster Volkswagen Golf 4
    Posted on 24 October 2022 by Scegli Auto
  • How to disassemble the cabin filter Citroen C3
    Posted on 23 October 2022 by ScegliAuto
  • How to replace shock absorber Opel Zafira 2008
    Posted on 23 October 2022 by ScegliAuto
  • How to fold the rear seats Renault Grand Scenic
    Posted on 22 October 2022 by ScegliAuto
  • How to remove the door trim Chevrolet Matiz
    Posted on 20 October 2022 by ScegliAuto
  • How to reset the tire pressure warning light on a Jeep Compass?

    DIY

    Frequently asked questions about cars and motorcycles
    1. by car
    2. :
    3. Jeep
    4. :
    5. Compass
    6. : How do I reset the tire pressure warning light on a Jeep Compass?

    Jeep Compass - Video Lesson

    Model: Jeep Compass MK 1, MK 49 - Years 2006-2016
    Part: inspection and maintenance
    operation: How to reset the tire pressure warning light on the Jeep Compass?

    When the tire pressure warning light comes on in combination with an audible signal on the Jeep Compass display, it means that at least one of the four tires is under-inflated. For the warning light to go out, the respective tires must be returned to the correct set pressure. The recommended pressure can be found on a sticker on the door pillar on the driver's side or in your vehicle's owner's manual.


    Learn more