Are you looking to remove white lettering on your tires? If so, you’re in luck! In this blog post, we will discuss a few different methods that you can use to get the job done. We will also provide some tips and tricks that will make the process a little bit easier.
So, whether you want to restore your tires to their original condition or just want to change the color of the lettering, read on for information on how to remove white lettering from tires!
When it comes to removing white lettering from tires, the most common kind of lettering to remove is the stick-on tire lettering.
Removing stuck on white lettering can be done with a few different methods, and we will discuss a few of them here.
To remove stick on white lettering from your tires you will need to use a few rounded tools. These rounded tools will ensure that when you are removing the lettering that it does not scratch or damage your tire.
You will need to use these tools to help pry and pull the lettering off your tire. If you accidentally you slip and hit your wheel, a rounded tool will also ensure that you do minimal damage to your wheel.
Stick on tire letters uses a strong adhesive keep the lettering in place, which means that it can be difficult to remove. However, there are a few ways that you can make the process a little bit easier.
One way is to use a heat gun or a hairdryer to heat up the adhesive. This will help to loosen the adhesive and then make it easier to remove the lettering using your tools. Be careful not to overheat the area as it could cause the tire to break down and begin to melt.
Another way to make removing stick on white lettering from your tires is by using a solution of soapy water.
This will help to break down the adhesive and make it easier to remove the lettering. This should not affect the tire itself, but it is always best to test in a small area first before applying it to the entire tire.
We would avoid using strong cleaning agents such as bleach or acetone as these can result in damage to your tires by causing them to dry out or to expire prematurely.
Once you have removed the white lettering from your tires, you may notice that there is some residual adhesive left behind. This can be removed with a little bit of elbow grease and a tire cleaner. Apply the tire cleaner to a rag and then scrub at the residual adhesive until it comes off.
If you are struggling to remove the adhesive, you can also try using a little bit of WD-40. Just be sure to wash the area well with soap and water afterwards as you don’t want to leave any oil on your tire.
The other kind of white lettering on tires may be as a result of them being painted .
There are a few different ways that you can remove white lettering from your tires.
One popular method is to use a tire cleaner or degreaser. You can find these products at most auto parts stores. Simply apply the cleaner to the lettering and let it sit for a few minutes. Then, use a firm bristled brush or rag to scrub the lettering off. You may need to repeat this process a few times to get all of the lettering off.
Another method that you can use to remove white lettering from your tires is by using isopropyl alcohol or rubbing alcohol. Simply apply the alcohol to a rag and then rub it onto the lettering.
The alcohol will help to break down the paint and make it easier to remove. You may need to repeat this process a few times to get all of the lettering off. Just be sure that you don’t use too much alcohol
as it can result in damage to your tires.
If all else fails or the white lettering is built into the tires, other than buying or replacing the tires, your only choice may be to paint over the lettering. You can use a tire paint or even just regular spray paint to cover the lettering. Just be sure to let the paint dry completely before driving on the tires.
Looking around and reading other guides on removing white lettering from tires has led us to consider a number of other techniques. However some of these should be avoided!
As we mentioned before, using harsh chemicals such as bleach or acetone can result in damage to your tires. These chemicals can cause the tire to dry out, which will lead to cracking and eventually failure.
Never try to remove white lettering from your tires using a knife or other sharp object. This can result in damage to the tire, which could cause a blowout while you are driving.
Sanding down your tire is another technique that should be avoided. This can result in damage to the tire, which could cause a blowout while driving. Some white lettering is built into a tire as well meaning that you would need to remove a large amount of rubber to get deep enough to remove all the lettering.
Turning your tires around so that the white lettering is hidden on the inside is not a good idea. The majority of tires are directional, meaning that the tire and the tread has been designed to rotate in a particular direction.
By turning your tires around and have the white letters facing inwards, you are changing the direction that the tread is meant to rotate in and this can cause your tires to not work properly and will be far less efficient.
Now that you know how to remove white lettering from tires, you can restore your tires to their original condition or change the color of the lettering to something that better matches your style.
Just be sure to avoid using harsh chemicals or other techniques that could damage your tires.
We hope that these tips and tricks have helped you learn how to remove the white lettering on tires. If you have any questions then please leave a comment below or get in touch via email or through social media and we will read and respond to every comment, email or question. Thanks for reading!
You recently installed new tires on your vehicle but don't like the way the white lettering stands out. So now you want to remove the white text. But how exactly do you go about doing that? We researched some ways to remove white lettering on tires, and here's what we found.
The steps to remove white lettering on tires often depend if you're removing paint or custom stickers. Here’s a quick look at the process for removing this text from your tires:
Custom tire sticker removal:
Before you continue reading, let us say we hope you find the links here useful.
If you purchase something through a link on this page, we may get a commission, so thank you!
Painted letter removal:
At first, these procedures may look relatively straightforward. However, one mistake may damage the tire. Continue reading as we talk about these processes in greater detail. We’ll also tackle another solution to hide the tire’s lettering.
In this section, you’ll learn how to remove white tire lettering based on the graphic’s material.
Perhaps you bought a second-hand tire but it has a custom sticker on it. If so, you can remove that custom graphic by following these steps:
Use the rounded tip of the trim tool to start peeling the adhesive off each sticker. It’s a good idea to start on the edges of each letter, as it’s often easier than going for the broader areas.
Also, avoid using the sharp edge of the trim tool. Doing so may scratch or poke your tire, causing it to deflate.
Sometimes the stickers won’t come off completely with the trim tool. If so, remove the leftovers from the tires with the pliers.
You may also use the pliers instead of the trim tool. But the trim tool often provides better control than the pliers.
Use the flat side of the plastic scraper to remove the adhesive left behind by each sticker.
You can apply more pressure with the scraper than with the pliers or trim tool. But take note that it can be quite tedious to remove the adhesive from the rubber surface.
You can use a 60- or 80-grit sandpaper to remove leftover adhesive that you found challenging to remove with the plastic scraper.
However, it’s important to pay attention to your sandpaper usage. Otherwise, the rough material may remove the traction in your tires, which puts you and your passengers at risk of on-road accidents and injuries.
Check out this plastic scraper tool on Amazon.
You can also watch the video below to see a visual guide on the steps mentioned above:
Take note that the work needed to remove stickers from tires often depends on the material's dimensions. Check out our post on how wide tires are on average to help you gauge the effort required to remove tire stickers.
Before continuing this procedure, it’s important to note that you’re about to use fairly harsh chemicals. So make sure that you’re wearing safety equipment, such as nitrile gloves and safety glasses, to prevent these products from coming into contact with your skin directly.
Also, ensure that you’re working in a well-ventilated area. Aside from wearing a respirator or face mask, open the windows and turn on the fans in the area. Otherwise, work outside to avoid inhaling noxious fumes for extended periods.
After finishing the preparations, here are the steps to remove painted lettering from your tires:
Apply the citrus stripping gel over the lettering. Use a paintbrush if needed to spread the product to the desired areas.
Then, let the solution sit for at least 5 minutes.
With the brass brush, use a reasonable amount of pressure to get rid of the strip-covered lettering. It should only take a little effort with this tool to remove the paint. If it doesn't, you either need to let the product sit longer or you may have to apply more of the solution.
Don't worry if the paint-stripping solution isn't removing all of the lettering. Use the brush to remove as much of the paint as you can. Also, don't apply more force than necessary or you'll risk puncturing the tire.
Brushing the citrus stripper with the brass brush should leave behind residue. Clean this leftover with one of your microfiber towels. Doing so should also remove more of the paint from the tire’s surface.
At this point, some paint might still be in the corners on the outlines of each letter. Scrape that leftover paint with the nylon brush.
Again, only apply the necessary pressure with this tool to avoid scratching or piercing the tire’s material.
Once you feel satisfied with the removal, clean the stripped location with the all-purpose cleaner. Use the nylon brush to remove any leftover paint and stripping solution from the surface. Then, wipe this solution off with another clean microfiber towel.
Check out this product on Amazon.
You may also check out this video to see a visual representation of the steps mentioned above:
You might also be thinking about replacing your old tires with white lettering with a set that’s devoid of graphics, particularly for your Mazda 3. If so, check out some of the best tires for that car for some excellent candidates.
Aside from the direct removal of tire lettering, you may also choose to hide the design by painting the material.
If you wish to proceed with this job, here are the steps to complete it:
Check out this tire dressing on Amazon.
The video below will help you see this procedure in action:
Tire lettering, particularly stickers, may last up to 1,000 miles under standard daily driving conditions. However, you might expect the lettering on tires to only last about 150 miles if used on a race track frequently.
However, some tire letter stickers can last up to 40,000 miles. This high-quality lettering may not even fade over time. But expect to pay more than what you’d spend to purchase standard tire stickers if you want to buy quality lettering.
Professional labor costs to install tire lettering may range from $159 to $199 per set. Although car owners may choose to apply the lettering themselves, taking advantage of expert help might provide peace of mind and minimize the risks of errors.
You may spray paint tires, although it’s not advisable to do so because spray painting isn’t typically ideal for coating rubber material, especially car tires.
If you spray paint tires, it might result in unsightly cracking.
Check out the video below if you find it interesting to see the results of spray painting tires:
It boils down to preference. Some car owners don’t mind the white lettering on their tires. On the other hand, certain members of the automotive community aren’t keen on seeing white letters on tires.
Remove white lettering stickers from your vehicle's tires by peeling them off their surfaces. On the other hand, use a reasonably safe-to-use paint stripper, like a citrus stripping solution, to remove white tire lettering paint. Otherwise, you may also choose to cover white tire graphics with tire dressing.
I somehow caught fire to highlight the brand name on the tire (like on sports cars or on off-road tires), but everything turned out to be not so simple .
.. It turns out that there is no information on the Internet on how to draw on rubber / tires / wheels correctly.
The first step was to find something to draw with so that everything drawn would not fall off the next day. I started looking on the Internet, there are many options, from paint to marker. But I decided to stop at the marker, because. it will be easier to draw. The car at that moment was under repair and on winter tires, which means I had enough time to implement my Wishlist in the summer. It was very important that the paint with which we paint was elastic and resistant. And this turns out to be not easy. And the most interesting and appropriate (as I thought at the time) was the Edding 8050 tire marker with a 4mm tip. nine0003
Marker is specially designed for applying any marks and inscriptions on rubber, BUT this does not mean that it is suitable for applying to tires - as it turned out later. In general, I bought this marker and tried it in the evening.
In general, I painted one wheel with this particular marker in 2 layers, but I was not very pleased with the result. They are very uncomfortable to draw. The paint either does not pour out at all, or vice versa, there is a lot at once and spreads. In general, I got along well with him. It cracks and doesn't hold up well. nine0009 I don't recommend you buy this marker! This is how I tried the marker on the inside of the rubber.
Here the inscription has a border and is easier to draw. The paint will not spill over the edge. But on the outside, the inscription does not have a side and this complicates the process. Because excess paint may spill out of the letter.
Fortunately, my brother had another marker in the garage - the cheapest paint marker with a 4 mm tip. and the next wheel I painted with it. It was already easier with him, but the thick sting / pen / tip does not allow you to draw accurately. So I found exactly the same cheap marker, only with a 2 mm sting.
nine0003
And now with a thin marker, everything has become much easier and faster. I recommend this marker for painting tires. If for the first time it took me an hour for the first wheel, then it is many times less. As a result, the rest of the wheels were painted in 2 layers with a thin and cheapest marker. It is not necessary to paint in two layers, it also holds and the effect is the same.
As practice has shown, the brand that is specially for tires lasted the least - about 1 week (it soon decreased, possibly due to the fact that it was on the front right wheel), this is of course very little. After 3 not even the slightest trace remained. But the cheap paint marker is still holding up, although it is well worn. Top of the wheel covered with ink for rubber Soft99 (there will be a new post about this) - so the inscriptions look very impressive !!!
After following all the rules and with due care, you will get an excellent result. And if you still don’t shuffle the rubber on the sides, then extend the service life. But do not think that this coverage will last for a long time. The paint is not elastic and cracks. And flies away with time.
Here is the result from a simple paint marker after 2.5 months. nine0003 Marker on rubber after 2.5 months
As you can see, the marker is almost invisible. But there was no trace of the Edding 8050 marker in a week.
I covered the top of the wheels with Soft99 rubber ink (this will be a separate article) — this way the inscriptions look very impressive!!!
And this is how fresh inscriptions, which are one day old, look like. Updated the inscriptions so to speak. There was an ink on the wheels, which, after 2.5 months, was well hydrophobic. On the Internet I did not find information on how to wash off the ink. It turned out to be nothing complicated - I used "Galosh gasoline" and cleaned everything easily. nine0003
I hope you liked the review of markers for tires/rubber/tyres/wheels and now it became clear to everyone how to draw on car tires correctly, and if you have any questions, write in the comments.
White letters on tires | ATT TiresI give my consent to the processing of my personal data
ATT-Tires wheel stickers are made from premium multi-layer rubber with a self-adhesive backing.
High adhesive adhesion, elasticity and wear resistance are the main advantages of our stickers over competitors.
Operating temperature of stickers from -95 to +95 C
Average installation time for 4 wheels - 1 hour
Keeping a distance, you can wash safely
Dirt and water repellent finish
Ultraviolet is not terrible.
Does not yellow or tarnish
If something went wrong - replace the damaged elements
Can be glued over original tire inscriptions
I give my consent to the processing of my personal data
Ordinate
Ordinate
Order
0149
Order
Bright white lettering on car tires looks strict and elegant.
The letters themselves are made of high-strength materials, the unique structural multi-layering of this product will keep the strength and whiteness of the letters for a long time. The dirt-repellent surface will not allow them to look dull and not bright.
ATT-Tires offers you to distinguish your car from a number of other cars by using graceful white letters on the tires of your car. The color of the car in this case does not matter. The main idea is based on the contrast created by the white color of the letters in relation to the black tyres. On a black background, the white letters on the wheels are easy to read, which means it can be used for both personal and promotional purposes. You can put your company logos, the name of the sports club, of which you are an active member, on the tires. nine0003
White wheel decals can be installed by anyone in the shortest possible time. Simplicity and ease of installation allow, in case of force majeure, not to replace the entire inscription, but to dismantle the damaged part of the inscription.
This will save money and time on ordering new stickers.
White letters do not fade from UV exposure, do not turn yellow during operation and always look contrast against black tires. Confident legibility of letters while driving, thanks to the strobe effect, guarantees you curious and interested glances of passers-by. nine0003
Before mounting the letters on the wheels, the surface of the tires is degreased and treated with a special compound that fills the porous structure of the tire and securely adheres to the surface of the letter. With little effort, you can quickly install the stickers on the tires of your car or motorcycle.
The surface of the tire itself does not require additional grinding before sticking the letters, it is quite enough to wash and degrease the tire, it is not damaged by the chemical composition of the fixing material. The letters are easy to clean in conventional car washes and can withstand high-pressure jets without breaking or peeling off.
