by Jennifer S.
Is your Chevy Malibu Tire Pressure Management System (TPMS) Warning light on? Use these tips to reset it.
The light indicator is a notification to warn you of significantly low air pressure or high-pressure loss in your tires and is NOT to be ignored, as low pressure affects the vehicles overall performance such as:
To Check the Recommended Air Levels Needed:
To Reprogram the system, and clear the Warning Light, follow 1 of these Options:
Contents
Be patient as this could take up to 30 seconds TIP: If you let the air out of a tire and hear 3 BEEPS that is notifying you that the reprogramming is COMPLETE and now you can add or release air to the proper levels if needed.
Lastly, via the MENU you can check to make sure ALL tires are filled to the recommended PSI levels, OR, you can check with a TIRE GAUGE. If any tire reads lower, you can add more air, or higher, remove some.
NOTE: If you are unable to Reprogram the Tire Pressure System on the first try, repeat the steps. If you are still unsuccessful, contact the dealership for assistance or consult your vehicle user’s manual.
The headlight for the DRIVER’s side should be LIT showing you where to START. TIP: If you let the air out of a tire and hear 3 BEEPS that is notifying you that the reset is COMPLETE and now you can add or release air to the proper levels if needed.
Lastly, via the MENU, then TIRE PRESSURE you can check to make sure ALL tires are filled to the recommended PSI levels OR, you can check with a TIRE GAUGE. If any tire reads lower, you can add more air, or higher, remove some.
In addition, if the tire pressure warning light stays illuminated past a week, you will need to have your vehicle serviced as there could possibly be a sensor issue or a tire puncture. NOTE: If you are unable to Reprogram the Tire Pressure System on the first try, repeat the steps. If you are still unsuccessful, contact the dealership for assistance or consult your vehicle user’s manual.
by Liam
It is common to check the pressure in the car tires as soon as we notice the TPMS indicator signals. Riding with even a slightly deflated tire or uneven tire pressure will imbalance the vehicle and is not advisable.
Contents
Ideally, people should be very careful about the tire pressure in their vehicles.
Once you ensure that all the tires are inflated according to the recommended limit in the manual, then the TPMS should also reset and start monitoring the tire pressure again.
Sometimes the indicator may keep the warning light on, and then you must follow the process to turn the TPMS warning light off. Chevy Malibu comes in many models, and here are tips on how to reset the TPMS in some of them.
This mid-range vehicle is named after the Californian vacation place Malibu. Chevrolet has been around now for a few decades and is liked by people for its Epsilon Platform, performance, and value for money.
You don’t need specific tools to reset the TPMS in the models sold between 2008 and 2011. The car’s remote key is the only device you need to make the TPMS relearn and reset the sensor. All the tires come with sensors, and the TPMS can monitor each tire.
These cars were manufactured for three-four years.
The following process is targeted at these models and will not work on other newer car versions. Here are the steps for TPMS relearn- reset process-
● You must fill the tires with air as per the PSI recommended level.
● Now take the car to a safe place out of traffic and park it on a flat surface. Ensure that the ground is even and not an incline.
● The engine must be switched off.
● Keep the handbrakes on so that the vehicle does not roll.
● Now use the car key to turn on the ignition.
● Do not turn the engine on as that will put the car system in motion. The car’s dashboard display and the software components will activate when the ignition is on.
● Now use the car’s remote key with both hands as you have to use multiple keys on that.
● Press the lock and unlock buttons on the remote simultaneously for at least five seconds or until you hear a sound. This will lead the horn to beep.
● This sound is the indication that the TPMS can be reset now.
The process starts when you hear the horn. Now you must check the tire pressure on every wheel. The dashboard will also show a tire learning active message.
● This is when the TPMS sensor activation process starts.
● First, check the driver’s side tire on the front. Take out the valve cap of the tire, and check the tire stress by reducing and filling the air in the tire. You might overhear a mild noise or sound coming from the horn once an optimum level of air is filled.
● Press the lock and unlock key again for the passenger front tire. Check the air pressure in the tire and adjust accordingly until you hear the sound of the horn.
● Repeat the entire process while using the remote key with both hands step by step. Start with the rear wheel on both sides.
● Once all four tires are checked and are completely at the optimum pressure, you will again hear a beep from the horn. This confirms that the sensor has noted the air pressure in the tire.
● This also indicates that the Tire Relearning process for the TPMS is complete.
● You will now see the message ‘Tire Learning Active’ on the dashboard disappear.
● You can turn off the ignition as the TPMS has been rested and can monitor the newly inflated tires again.
When you have to replace a flat tire using the spare, the TPMS may not recognize the new tire. It may detect low tire pressure, or the sensor may flash a message saying it is malfunctioning.
The spare tire may also need to be checked for air pressure as it may have deflated while kept in the car’s boot.
Check the air pressure in the new tire, adjust as needed, and then use the process mentioned above with the remote key. The sensor will have to relearn and reset for this tire too.
Some of the 2011 models may have a different system too. The TPMS relearn tool was added to the car in 2011. The process is similar to the older models and involves using the TPMS Relearn Tool.
● Use the lock and Unlock keys on the remote simultaneously until you hear the horn.
● Use the TPMS relearn tool near the tire’s valve and activate the TPMS sensor using the button.
● Make sure you follow the same steps for each tire as explained above.
There is another method to reset the TPMS with the help of the software tools embedded in the car using the dashboard. Switch on the ignition to activate the sensors and the dashboard.
Go to the menu, check the vehicle information, scroll down on the options, and reach tire pressure. Now choose the press and hold the SET button, and you will hear the horn beeps.
Starting from the driver’s side front tire, use the TPMS Relearn tool and activate the sensor for all the tires. After following through with all the steps provided, now you may start the engine.
Resetting the TPMS using the modern software embedded in cars is very simple and does not take more than a few minutes.
Do not forget to reset the TPMS when you change the tires or refill them.
The spare tire also may need a reset if the sensor does not identify it. It is essential as the sensor will flash when it can see that the air pressure is low in the tires.
Cars were and will be my first love and favorite hobby; I decided to start writing about my discoveries and techniques to improve my cars or repair them.
...
You are the proud owner of a recent car, the joy of tactile gadgets, integrated technology should bring you the convenience of using your Chevrolet Malibu, which is important because technology talks about electronic, and as we all unfortunately often know, violations often occur to allow . Today we will focus on the tire pressure sensor and specifically on the tire pressure sensor. how to reset the tire pressure sensor on a Chevrolet Malibu so that you no longer have this indicator on the dashboard.
nine0004 To do this, we will divide our article into two parts: first, we will focus on the general case of the tire pressure indicator light and the subsequent procedure, and then on the case when the tire pressure indicator remains on even when inflated. tires, so how to reset this tire sensor on a chevrolet malibu.
First, we will look at the common way to reset the tire sensor on a Chevrolet Malibu, which if it lights up, here are the basic simple steps:
nine0016 Now that you have completed the basic procedure for removing the tire pressure sensor on the Chevrolet Malibu, and it didn't work, we'll move on to the second solution, which is, the tires on my Chevy Malibu are well inflated and I still want that light to go away. This probably shows that you have Faulty tire pressure sensor. This will require to reset the value on your car's dashboard.
However, be careful not to do this while driving as pressure fluctuations will affect your pressure sensors. In most cases you need to go through the car settings then you should find an option to detect inflation or "detect deflation" once in this tab you should hold the select or reset button depending on the year of your Chevrolet Malibu until you see the message on the car console confirming that the reset is taken into account (usually takes a few seconds). You can now turn off the ignition and restart your Chevrolet Malibu to see if the tire pressure light has gone out. nine0005
However, this method is not recommended as it may result in mishandling and malfunction of your Chevrolet Malibu. Now you have all the keys to know how to reset the tire pressure sensor on a Chevrolet Malibu. nine0005 For more Chevrolet Malibu tips, take a look at the Chevrolet Malibu category.
Save article:
The article says:
When the tires are optimally inflated, the low tire pressure indicator (TPMS) does not light up on the vehicle's dashboard. However, in some cases, it lights up even if the pressure is normal. This can't help but be annoying, especially when the tires are inflated normally. In our article today, we will figure out how to reset a tire pressure error.
American and European scientists conducted a study, during which it was found that most drivers do not check whether the wheels are properly inflated before getting behind the wheel of a car. Only 40% of car owners perform such a check - and even then only once every 12 months. This is the reason for a large number of accidents. nine0005
The TPMS (Tyre pressure monitoring system) system is designed to monitor tire pressure, as well as warn of a malfunction. If the tires are under-inflated or over-inflated, an error will be displayed on the remote control or an audible signal will appear.
What is dangerous too high or, conversely, low pressure? The risk of an accident increases, the car begins to consume more fuel, in addition, the rubber wears out faster.
Photo: Shutterstock nine0005
The above devices operate on the same principle. Let's figure out how information about what tire pressure gets to the control panel.
Consider how pressure is calculated by measuring instruments. Typically, the sensor performs a comparison of the angular rotation of the wheel.
Knowing the value of this parameter, you can calculate the distance that the wheel will travel in one rotation.
Obviously, if the tires are under-inflated or over-inflated, then the outer diameter of the wheel will be different. Visually, a person cannot determine this change. But the sensor notices even such changes. The system fixes non-compliance with the required parameters. nine0005
The sensor will still respond, despite the fact that the wheel circumference has changed quite a bit. In this situation, it is necessary to find out what mechanical reason led to this. Only in this way can you eliminate the misinterpretation of the signals transmitted by the system. This can happen because:
Also, the TPMS system gives an error when you install new wheels or rearrange them.
When, after these steps, a tire pressure error appeared, indicating unbalance, you should reset the settings, and then set the basic parameters. In this case, the control signal may remain even if the basic settings have been selected.
Why such problems may occur:
At the same time, as soon as you drive out onto an asphalt surface or start driving calmly, the error disappears. nine0002 See also
"Velcro or spikes: which rubber is better for the Russian winter"
Read more
How to reset tire pressure error? To begin with, imagine that the TPMS system is working properly and the blinking light indicates a problem with the undercarriage of the machine. The first thing you should do is slowly release the gas. You can not brake sharply, turn the steering wheel. After the car has stopped, inspect the tires to make sure the rubber is not punctured or broken. Then you can check if the tire pressure is normal. nine0005
Pay attention! The TPMS will not always show a tire pressure error. For example, if the tires are slowly deflating, the system will not inform you about the problem.
In the same way, she will not notice the error if the tire pressure starts to drop rapidly. This usually happens when a tire ruptures. This feature of the TPMS system is explained by the specifics of identifying and counting nonconformities.
However, in some cases, it happens that the TPMS system indicator is on, but the tires are in perfect condition. How to reset tire pressure error? We understand. nine0005
The complex TPMS system in some cases starts to work incorrectly. Usually, car owners observe the following picture: a tire pressure error is displayed on the display (the tire is underinflated), but in reality everything is fine with the wheel. You have to reset the tire pressure error. Otherwise, the TPMS system starts to work incorrectly.
Photo: Shutterstock nine0005
You also have to reset the tire pressure error when there is radio interference from high voltage power lines.
Or when sources of radio signals are located in the immediate vicinity. But as soon as you move away from them, the pressure error disappears and the system begins to function properly.
The reason for the malfunction may lie in the sensor, which is "failed". This damage cannot be easily repaired. How to reset a tire pressure error if the sensor flashes, while you hear a beep, lose your vigilance and find it difficult to drive a car? There are 4 ways to fix this problem. nine0005
To reset the error, pick up a speed of 80 km / h and continue driving for another 15 kilometers.
This method is the easiest to implement. If your car has this feature, then turn on the cruise control so that the speed does not change. Depending on the model of your car, you will be able to reset the tire pressure error at a speed that exceeds the specified one. After you cover a distance of 15-20 kilometers, maintaining the same speed of 80 km / h, make a stop.
Turn off the motor. When you start it again, the tire pressure error will disappear. nine0005
Popular articles
How to choose a subwoofer for your car
19.12.2022
192
From top to bottom, obliquely: how to degrease a car body before painting
12/15/2022
135 nine0005
Chic, shine, beauty: how to remove scratches on a car with your own hands
9.12.2022
197
Without damage: how to reduce the fuel consumption of your car
11/29/2022
227
nine0054 How much do they pay for advertising on a car11/25/2022
559
Press the tire pressure monitoring system (TPMS) reset button on your car and you will be able to reset the error.
It does not matter what type of low pressure warning system is used. In any case, there will be a sensor on each wheel of your car. Sometimes it may be necessary to reboot the touch system of the car. Read the owner's manual for the vehicle. It contains information on how to reset a tire pressure error. Most often, the instructions indicate which button to press to reset. nine0005
The ignition key must be in the lock. No need to start the car, just turn it to the “on” (“ON”) position. Then press and hold the reset button, which may be under the steering wheel. We are waiting for the low pressure indicator to blink 3 times. After that, you can release the button. We start the car, it should work for 20 minutes. After this time, the computer will calibrate the sensors on the wheels. Now you can turn off the car.
nine0002 See also
""
Read more
Lower and then re-inflate the wheels.
Failed to reset tire pressure error using the previous method? Then we inflate all tires to 0.2 bar, this is the pressure that should be according to the recommendations of car manufacturers. Did the error go away? Then we lower the pressure in the tires completely.
Now we pump up the wheels again. The pressure in them should be the same as indicated on the driver's door pillar or in the car's operating instructions. When there are sensors on the wheels, you need to remember about the spare tire. Now you need to drive about 3-5 kilometers, adhering to a speed of 25 km per hour. So you can reset the tire pressure error. nine0005
Remove the battery terminals and then connect it to reset the error.
Each car has a computer that receives data from all kinds of vehicle sensors, including TPMS system sensors. However, any electronics can fail. To reset the error, you will have to reboot the system, for which you need to turn off the power.
Photo: Shutterstock
To do this, open the hood. The battery is located under the hood. Disconnect the negative terminal from it. To perform this operation, use a wrench. Then sit in the driver's seat, turn the key to the "ON" position, but do not start the car. Now you need to press the signal for 3 seconds. This will use up the energy that remains in the electrical system of the machine. Then reconnect the battery. This way you can reset the error. nine0005
Sensors keep track of tire pressure. However, you need to be sure that they function properly. Of course, you do not need to constantly walk around with a special measuring device and find out the status of the sensors. It just needs to be calibrated from time to time.
It is performed quite simply. The most important thing to remember is that, depending on the make and model of your car, for each wheel there are pressure parameters strictly defined by the manufacturer for winter and summer.
These values should be given to the sensors. How the installation and configuration will be performed depends on the controller used. nine0005
Experts do not recommend using the internal controller yourself. However, additional settings are not required if the data is read using the screen that is directly on the control system. For current promotions on the Halva card, which will help you profitably purchase household appliances, you can follow here. nine0005
To prevent a tire pressure error from appearing, it is important to calibrate (adjust the TPMS system) every time a change is made. For example, when you installed a new set of wheels, repaired tires, did balancing, and the like. Using TPMS controllers is quite simple. The main thing is to read the instructions for use of the device. And make sure that the tire pressure is the one recommended by the car manufacturer.
nine0002 See also
"What tires can be put on rims 14, 15 and 16: advice from professionals"
Read more
Every car owner gets annoyed if the tire pressure error icon lights up on the dashboard.
