Tire Education
byJames Updated on
Whether for proper tire disposal or for recycling into ornamental, farming, or gardening purposes, cutting tires in half is the most sensible thing to do with your old, scrap tires. However, tires are built with durable rubber to withstand extreme abuse and are wrapped inside with high-tensile metal belts, so you’ll need to be equipped with the right tools to get through them.
To cut tires in half, you can opt to choose between two easy-to-follow processes: First is by removing the sidewall with a knife or any sharp and pointed tool through the seam found in the sidewall just below the tread. The second is to reduce them into more manageable pieces with the use of power tools such as a jigsaw, circular saw, or Dremel tool equipped with metal cutting blades.
What You Need To Consider Before Cutting TiresBefore you proceed with cutting tires, you must first check with your community if there are specific regulations on tire handling and proper disposal. Because tires are made with man-made rubber, they are non-biodegradable and their chemical composition can seep into the ground. That is why some local ordinances are very specific on this aspect.
Since scrap tires or old tires are considered solid wastes, they are regulated primarily by state governments. As of writing, there are already 48 states that have specific laws or regulations in dealing with scrap tires management. While each state’s program is unique, proper delegation on handling, disposal, and recycling are the common themes.
Proper disposalIf you will cut tires just to easily dispose of them, without the consideration of reusing or recycling, you should also consider your local or municipal regulations. Some municipal ordinances have tire disposal guide requirements. For example, some specific guidelines mention that tires should be cut into a minimum of two pieces.
SafetyWhen cutting tires in half, you’ll be dealing with sharp and pointed tools for piercing through the sidewall and/or cutting through the tires’ tread.
That is why safety must be observed at all times, keeping the tools away from the body is a good start.
Additionally, rubber fragments left after cutting tires vary in size, from considerable chunks to clouds of dust. This may have a chance to go through your nose or eyes which will cause irritation. On the other hand, the emitted fumes which resemble burning rubber can be toxic at moderate levels. Lastly, the exposed portion of steel belts is very sharp, so take extra precaution when handling cut tires.
How to Cut Tires In Half Method 1: Without The Use of Power ToolsTools you’ll need:
The ‘sweet spot’ of the sidewall is the softer and smoother part about one inch near the tread. This is the weakest point in the tires with virtually no reinforced belts.
Having said that, avoid cutting too close to the tread nor too close to the rim as these portions are saturated with steel belts.
To do this, strike the sidewall with the tip of the blade forcefully. If you’re having trouble, or unsure that the blade will just slide through, an awl, ice pick, or any similar pointed tool will help.
Step 2: Secure the tire to prevent it from rockingThe tire will likely roll or move while you’re slicing through the sidewall. To prevent this from happening, lay the tire flat on the ground, then step on the opposite section of the tire, away from where you are cutting. Another way is to keep the tire upright, locking your foot or thighs to prevent it from rolling. However, you should practice extra caution in this position and make sure that you are cutting in the direction away from your body.
Step 3: Cut through with a sawing motionYou can gain momentum if you are cutting with a sawing motion. Some tires have seams running through the sidewall, one near the tread and another near the rim.
Make use of them as your guide while cutting through. When cutting along the sidewall, there will be a point that the blade will be harder to cut through the rubber. This is naturally brought about by friction, you can spray the blade with a lubricant and you’ll immediately notice the difference.
Wooden dowels keep the cut area open, making it easier to cut through the rubber. These dowels pry apart the rubber on both sides, preventing the blade from being stuck.
Step 5: Continue cutting until the sidewall detachesIf you’re already halfway through, rotate the tire a little half to get a new position to continue. This will make the process easier. You can also use your free hand to pull the other side of the sidewall to help you slice through.
How to Cut Tires In Half Method 2: Slicing into Small PiecesTools you’ll need:Cutting tires with power saws will leave behind lots of rubber and metal fragments, not to mention the fumes cut tire will emit during the process.
Work in a secured location with proper tools and equipment to promote a safe, efficient, and neat tire cutting activity. If you will be working outside with no power outlets available, ensure that the extension cord you are using is rated for high-voltage applications.
Any tire, regardless of its size, is stuffed with high-strength steel belts, with larger tires equipped with more reinforced steel. This is why it is necessary that the blade you’re using has the capability to cut through metal. Ferrous-metal cutting blades or metal grinding wheels will safely and efficiently do the task.
Also, wear your personal protective equipment such as safety glasses and a dust mask. The use of protective arm sleeves and gloves is also recommended to protect your limbs against metal shards flying out of the tire.
Step 3: Cut widthwise through one sideAs your tire is laid flat on its side, press the blade laterally across the sidewall, working your way slowly from the tire’s inner lip to the edge of the tread.
Keep in mind that the innermost tough part of the tire, called a bead, has a bundle of high-tensile steel wires wound into a rubber band. You may feel a slight resistance on this part but there’s nothing to worry about if you’re using the right type of blade.
Step 4: Complete the cut from the opposite sideFlip the tire over to cut on the second side, applying the same trick done in Step 3. Then, cut across the tread to completely separate each end of the tire. Next, turn the tire 180-degrees and repeat the process to have a tire neatly divided in half.
This technique will save you a significant amount of time and energy as cutting this way reduces strain brought by the resistance of inner steel belts holding the tire together.
Step 5: Continue cutting in halvesLike slicing a pie, continue cutting each pair of the tire equally into smaller sections until you’ve reduced it to quarters or eights. As the pieces become smaller, they’ll be prone to moving and sliding due to the reduced weight, keeping them in place with a vise or similar clamping tool will help.
Tire cutting, if not planned correctly, will entail additional yet unnecessary time, not to mention the extra effort that can be prevented in the first place. There are a few recommendations to consider such as starting the cutting process by piercing the sidewall with a pointed tool instead of the same cutting tool and avoiding cutting directly through steel belts manually.
Make a strong start by piercing a hole in the sidewall with a pointed toolUse an awl, ice pick, or any similar tool that can be used for poking into the tire. This way, you’ll reduce the pressure you’ll exert into striking the tire if you will be using a knife or box cutter.
Cutting directly through steel belts is time-wasting if done manuallyUnless you’re using a power tool, cutting directly through steel belts by hand requires too much effort, let alone your tool could dull or get damaged blades.
Leave the cutting of tread and bead to a jigsaw, circular saw, or Dremel tool.
If you will be working with car tires, the process will be the same regardless of the size, as you will deal with the same steel reinforcements. If you don’t have any power tools in hand, you can use a good old hacksaw or a big pair of steel shears, though be prepared for a more tedious task, you’ll probably hurt your hands too.
Can I cut a tire off a rim?Yes, it is possible. In fact, with the right angle, you can cut through easily and as close as possible to the rim. However, the challenge is to keep the angle of the blade correct, as you don’t want the blade hitting the rim.
ConclusionThe tire cutting process may look intimidating at first. This thought may be brought about by the use of high-powered tools and patient dealings with tough tire rubber materials.
However, if done correctly, and equipped with the right tools and equipment, you can get through with this process with ease. Just remember to put your safety first at all times.
Do you have a used tire and don't know what to do with it? Believe it or not, tires can be recycled and used in a variety of ways. But before they can get recycled, reused, or properly disposed of, they need some preparation. One way to do so is by cutting them up. We did some research and here's what we found out.
When you have a tire that you need to discard, the best way to do it is by cutting it up into small pieces. You can either quarter the tire, or cut it out circumferentially before putting it in a landfill. In order to do this, you need some cutting tools and equipment.
Cutting tires for disposal makes it much easier to transport and it will take up less space. In this blog post, we will show you how to cut tires for disposal in a safe and effective manner.
And, we'll answer related questions. Keep reading to learn more!
Before you continue reading, let us say we hope you find the links here useful. If you purchase something through a link on this page, we may get a commission, so thank you!
Tire cutting is breaking down a tire into smaller pieces for easier transportation and processing. With the right tools and some careful planning, cutting tires for disposal is a breeze.
When cutting a tire, safety is essential. Here are some precautions you should take before and during the process:
Now that you know what safety precautions to take, let's move on to the tire cutting process.
But one last reminder. Cutting tires may look easy, but it is a difficult task that requires strength and focus to avoid accidents and mishaps.
This is the first step prior to the actual cutting part. Make sure that there are no valve stems or caps left on the tire.
Cutting directly through the steel belt will make your efforts futile. It may hurt your hand or damage your cutting materials. 
Once cut, you can take tires to the following for proper disposal and recycling:
If you don't want to cut up your old tires, you can always recycle them or use them for other house projects.
Here are some reasons recycling tires is important:
You can recycle or repurpose old tires in different ways.
We've listed some of them:
There are many ways you can use whole tires for your home:
Here's how you can turn your old tire into a swing for your kids, or even for yourself.
Position your tire where you want it in your yard or maybe even inside your house. Then fill it with some stones and soil, and you have a brand new planter.
Get creative with an old tire by spray painting it, then letting it dry. Put some old blankets to make your pet comfortable in its new tire bed.
If you have enough tires, you can use them to create a garden project.
Arrange the tires to add some height and levels in your yard.
Old tires can give your driveways and pavements a new look and can even save you money! It might take you some time to do it, but it will be worth it in the end.
First, stack 2 to 3 tires together. Then, place a trash bag inside the stack to contain your garbage.
If you're creative and resourceful enough, you can do the following projects with your rubber scraps. You'll just need a few other materials.
Cut the tires into shapes that you like. With a little preparation and glue, you'll end up with brand new floors made from your old tires.
Do you have a knack for arts and creativity? You can also turn your old tires into a masterpiece!
Have your tires shredded into smaller pieces. Lay them in your garden area where desired.
We can recycle tires in more than several ways.
They are useful as new tires, playground surfaces, and even furniture. So, the next time you have an old tire that needs discarding, remember that recycling is the best option!
Thick black smoke released from burning tires can stay in the air for long periods of time. This contributes to global warming, so avoid burning tires.
Small particles inhaled from burned tires are also dangerous to your health. They can lead to asthma attacks, acute respiratory symptoms, and put children, elderly adults, and pregnant women at risk.
It can take anywhere from 50 to 80 years for a tire to decompose. But the fact is, it will take almost 2000 years for tires to revert back to nature. Therefore, it's so important to recycle or dispose of tires properly.
Depending on how often you drive and the type of roads you travel on will impact how often you need to change your tires.
Typically, you'll change your car's tires every 3 to 5 years.
Cutting tires for disposal is a safe and effective way to recycle or dispose of used tires. Ensure that you properly prepare tires for recycling and disposal by following the steps above. Thanks for reading!
We hope this blog post was helpful! Feel free to share this with your friends who may have some old tires and don't know what to do with them.
If you're still here, you may be interested in reading the following articles:
How To Remove Studs From Tires
Do Tires Degrade Over Time? Even When Not Used?
12+
11 months ago
COUNTRY PARTISAN ☭697 subscribers
Do you want to do anything to the dacha with your own hands, the simplest thing is to do something from a car tire, on the channel, Dacha with your own hands.
------------------------------------ How to cut a tire, for someone it’s news that you can cut a tire with a jigsaw. ------------------------------------ If there is no jigsaw, then you need to urgently and quickly buy it. Whatever you think about how and how to cut the tire. ------------------------------------ All these methods of cutting with a knife and a grinder are very dangerous. With a knife you can cut off your fingers or, even better, pierce your stomach and in terrible agony, drenched in cold sweat, writhing in front of the tire. ------------------------------------ With a grinder, you can damage your eyes with a piece of metal cord that has flown off. It’s good if one eye remains to admire your crafts from tires in a country house made with your own hands. ------------------------------------- Not every jigsaw can cut a tire. Buy at least 1000 watts. There is a question, how many files go to one wheel, the answer is not at all. One file is enough for ten tires, after which it becomes hopelessly dull and breaks from grief.
-------------------------------------- Files must be bought for metal, and of medium size in the sense of cloves. There are three sizes 1, 2, and 3. The second size cuts rubber best, and it also cuts metal cord without problems. -------------------------------------- Tires can be taken completely free of charge at any tire shop, if you are offered to buy them, then you can safely send them and go to another, good tire shop. To get rid of accumulated unnecessary tires, tire fitters need to pay for removal and disposal, so they must pay you, they gave me a medal “For removal”. -------------------------------------- In the video, even without comments, you can see how to cut a tire in four minutes. Tires Japanese 285/70 R18 with a steel cord on a protector. Of course, you need to have a firm hand, a cold mind and a warm heart, and so that the idea illuminates the path to the goal. And the goal is a do-it-yourself cottage where you can relax and have fun. -------------------------------------- #do-it-yourself dacha #homemade for dacha #ideas for dacha #dacha partisan ------------------------------------ ✔ Subscribe to the channel.
By clicking on the bell, which is located next to the subscribe button, you will receive a notification about the release of a new video on the channel. ---------------------------------------- ☻ If you want to support the channel - share a link to my channel, or a video you like, or tell me about me on social networks, or you can transfer a certain solid amount of banknotes only in ₽, ☢ Contribution, mite, contribution, offering (sacrifice). Page of voluntary donations for the development of the channel - https://yoomoney.ru/to/410014880180666 keywords: how to cut a tire lengthwise, how to cut a tire with a knife how to cut a tire in half how to cut a tire with a metal cord, how to cut a tractor tire how to cut rubber with a grinder, how to cut a tire from belaz, the better to cut a truck tire, how to cut a tire with a steel cord, how to cut a tire for a flower bed, how to cut a car tire
Indeed, they do not rot and do not spread from the sun-frost.
Accidental blows, unlike asbestos-cement sheet, do not harm them. After all, there are many applications for rubber bands. Even if you don’t turn over the beds, like mine. Even if not cut tire on the tape, the hoops obtained from it can be used as a compost box or a vertical bed. Yes, one hears a lot that, they say, it’s harmful, terrible and all that. Don't know. But my ants, it is near the rubber, that they arrange their summer masonry-incubators, where they keep their pupae. Whether from rubber harm - I do not think that they would have worked like that. And if they are not afraid, then I somehow do not fit.
OK. Everyone decides this question for himself. But who decided to cut the tire for their needs - so a few tips:
Start cutting the tire with a shoe knife. We carry out several times on the same cut, pressing on the board so that the cut diverges and cuts through. Now we insert a good knife into the cut, sharpening towards ourselves (I made a special cutter from an industrial hacksaw blade) and cut with an “up-and-on” movement, simultaneously bending the cut to the side.
Cut the tire like cutting bread - no need. Rip up the rubber. And it is not necessary for a knife to be razor-sharp: a slight sawtooth burr is only good.
I recommend turning the tire inside out for the winter and letting it mature. Otherwise cut, it will become a wave. It is necessary to remove the trough shape, which will give a long aging of the hoop. And you can do it differently. Make a bunch of cuts on the inverted tire.
You can cut hoops into ribbons with an ordinary, small grinder. Just take care that the wind is not on the neighbors, otherwise you cannot avoid an untranslatable pun (in one of the local dialects) because this is a stinky business. BUT! The rubber is nicely cut off by a grinder, the metal cord is also striped by it. In general, cutting a tire is a quick business if you see how once. And to make it completely clear - here's a video for you, where the tire cutting takes place in real time.
When processing and manufacturing products from old tires, there are pitfalls that are hidden from view, and appear only directly in the process.
This article is devoted to these stones.
The tire must be firmly fixed, or at least the part that is currently being cultivated must be fixed. In our case, an original technique for cutting tires has been developed. Based on this, it is necessary to cut the tread first of all while the tire has maximum rigidity. If there is, you need to cut the protector and not rest against anything, a bull glass jar will come to the rescue, although after sawing 5-6 centimeters, the jar needs to be moved.
The threads of old and new tires are different and the results i.e. the properties of the cutting elements are different. For clarity, if you make a swan from a bald tire, then the head of the swan falls into the front, and if from an almost new one, on the contrary, the head is thrown back.
The metal cord is located only over the entire area of the rubbing surface.
The metal cord, together with the thickness of the tread itself, creates additional difficulties when cutting the tire.
It is very, very difficult to cut a tire with a hacksaw, and in some places it is completely impossible.
When processing the main rubbing surface, use:
But the sides of the wheel are easily cut with an ordinary knife. Rarely, but aptly, there are tires without a metal cord at all - probably 1 out of 40.
The ring is a hardened stranded metal rod bent into a ring. Cutting with a hacksaw for metal is unrealistic, but it can take a long time. The only way out is to use Balgarka. I think it's called the seat ring.
Many immediately want to get rid of the ring in some cases, the rigidity of the ring is used in the design.
Wheels can be painted with any paint. Nitro enamel dries quickly, and allows you to immediately place and use the figures. But since rubber has to be painted, which deforms during transportation, the paint also cracks and bursts - regardless of the type of paint. Since the chemical reaction goes on constantly, therefore the colors fade, the white becomes with a yellow tint, so it is better if it is possible to repaint the figures every year.
Since the cord is a metal mesh, therefore, metal hairs are formed on the cut, which strive to cut through the skin. Metal shavings are not a pleasant splinter. Be especially careful with the eyes when sawing with a jigsaw.
I would like to immediately warn, but not to scare or dissuade, that the tire weighs quite a bit, and working with cord and a metal nozzle ring implies the presence of male hands.
On average, wheels of 13, 14, 15 radii - the most popular ones weigh an average of 5 to 8 kilograms, and if you judge that one cutting can take about 1 hour, then you will have to turn the wheel more than once.
For processing, cutting of an old tire, you need:
if you cut ALONG (along the circumference) then . FIG knows he did not cut. perhaps a sharp knife and soap as advised above or a jigsaw.
is again - if you don’t run into a cord.
A video on how to cut the tire can be viewed on here.
Source mastedom.ru
Because the surface where the tire touches the ground is more difficult to cut because there is a metal cord.
To do this, you can use it like a hand saw, lubricating it with oil or soapy water, or a grinder with a metal disc.
I must warn you, if you have never used a grinder before, it is better to use a hand saw, since it is not difficult to catch the disc clamping when cutting the tire. For this procedure, you need to firmly hold the tool and be able to cut correctly.
Since the cutting is carried out with a sharp knife, which is constantly moistened with soapy water, oil or at least water.
When cutting, it is best to pull back on the cut piece to reduce the resistance to the knife.
This procedure is indispensable in the manufacture of various homemade products from tires, from flowerbeds of various designs to original garden figures and sculptures.
Source sam0del.ru
Modern industry produces many different types of rubber used in the most unexpected industries. Quite simply and quickly, you can find the right rubber gasket or the necessary rubber blank at the nearest bazaar. However, if you still need to make a rubber product with your own hands, then a couple of simple tips on how you can simply and accurately cut rubber will come in handy.
Rubber can be quite diverse in its properties, ranging from a very elastic and rather pliable material to elastic, durable rubber plates. The use of rubber can be found in a wide variety of ways, for example, cutting a suitable plumbing gasket, a heel for boots, or a non-slip support under a glass surface. Many carve out various kinds of animals from car tires, swings, or make interior items. You can make flower beds from car tires, but for this you need to know how and with what to cut a car tire.
The secret is very simple, in order to neatly and simply cut a piece of rubber, you need a sharp knife, of course.
and ordinary water.
A piece of elastic rubber, a sharp knife and water.
First you need to mark the line of the cut (I just needed to set the knife blade evenly).
Start cutting rubber with a knife.
Cutting thick rubber with a knife becomes quite difficult as the blade goes deeper into the thickness. Rubber starts to become viscous, and if overzealous, the rubber can even melt. To prevent this from happening, and the knife went through the rubber like clockwork, it must be moistened with water (and not with oil, in no case should it be moistened with oil).
Wet rubber with water and cut with a knife.
Rubber gets slippery when wet and the knife blade won't get stuck or melt the rubber, so you get a clean, quality cut without much effort.
Water-cut rubber block.
Sometimes there is a need to cut circles of rubber, for example, for non-slip feet under a stool, heels, or for spacers between two glasses.
In order to cut rubber mugs of an even shape, you need to choose a metal pipe of a suitable diameter, you will also need a piston that is suitable for the diameter of the tube.
A - metal tube, B - piston
You need to sharpen the edge of the iron tube with a sharpener or file.
Sharpened iron tube
After you have sharpened the tube, you need to insert it into the drill chuck, moisten the rubber with water and simply start drilling holes, after laying the piece of wood.
Drilling round rubber pads
Using this simple tool and water, you can drill as many smooth, neat rubber rounds as you like (I use them to make non-slip feet for appliances). The sharpened tube acts on the principle of a drill, but as the circles are drilled, it is filled with them, and in order to pull them out, a special piston is needed.
You then simply push the rubber rounds out of the sharpened tube.
Squeezing the rubber out of the tube with a piston
The main thing is not to forget to moisten the rubber with water when drilling or cutting.
It should be noted that cutting a circle using a sharpened tube is much easier and more convenient than using a drill in the classical way. However, if you need to drill through the rubber with a drill, it is also quite simple to do this by first sharpening it sharply, and periodically dipping the drill into the water.
It is necessary to drill rubber at low speed and periodically wetting the cutting edge. However, if you need to drill through a large block of rubber at high RPM, you may want to submerge it completely in water.
Drilling rubber in water with a drill.
In the most extreme case, holes in thin rubber, as well as in plastic, can be melted by heating the drill shank or iron tube with a lighter.
Holes fused in rubber
Above all, be careful when working with hot metal. Also remember that rubber can release toxic substances when overheated, so melt holes under a hood or in a well-ventilated area. Follow all safety regulations even when drilling rubber.
When you need to cut a car tire (tire) with your own hands , it is better to know some tricks that will not only help make this process more enjoyable and less time consuming, but also help protect yourself from injury and make the cut better.
Because the surface where the tire touches the ground is more difficult to cut because there is a metal cord.
To do this, you can use it like a hand saw, lubricating it with oil or soapy water, or a grinder with a metal disc.
I must warn you, if you have never used a grinder before, it is better to use a hand saw, since it is not difficult to catch the disc clamping when cutting the tire. For this procedure, you need to firmly hold the tool and be able to cut correctly.
Since the cutting is carried out with a sharp knife, which is constantly moistened with soapy water, oil or at least water.
When cutting, it is best to pull back on the cut piece to reduce the resistance to the knife.
This procedure is indispensable in the manufacture of various homemade products from tires, from flowerbeds of various designs to original garden figures and sculptures.
Category: Auto repair manual
Characteristics of the car: Dimensions of the car are as follows, length - 3826, width - 1100, height - 1323 mm. The wheelbase is 2382 mm. Ground clearance 211 mm. The car is equipped with a hybrid powertrain. The 2-cylinder engine is equipped with a system that provides the output power of the motor. There are 4 valves per cylinder.
Single cylinder diameter 72 mm, stroke 70 mm. The engine crankshaft and accelerates to 8000 rpm. The maximum torque is maintained up to 3000 rpm.
Posted by admin: at the request of Aristarkh
Watch the VIDEO about how to cut tires from Kamaz.
The reasoning of a car owner named Victor: The price is 309 thousand. A trouble-free simple car. Everything is repaired with a hammer and some kind of mother))) many people complain about the stove, but I have no complaints
Release date: 18. 10. 2013 years
Laughter in the topic: Grandma gets on the bus and everyone immediately became interested in looking out the window.
uazbuka.ru > Technical > General technical questions > What is the best way to cut a tire?
View Full Version : What is the best way to cut a tire?
For some purposes (when I'll show you) I need a piece of tread from an old tire.
What is the best way to cut a tire?
1. Bulgarian? (cuts, but stinks and everything is covered in soot)
2. With a jigsaw?
3. With a knife?
Who had experience share!
For some purposes (when I'll show you) I need a piece of tread from an old tire.
What is the best way to cut a tire?
1.
Bulgarian? (cuts, but stinks and everything is covered in soot)
2. With a jigsaw?
3. With a knife?
Who had experience share!
Solzhenitsyn in "The Gulag Archipelago" writes that convicts made boat shoes from car tires called "chuni from ChTZ" by cutting tires with 2 axes (one as a chisel, the second was beaten). And sewn with copper wire. 🙂
When operating a grinder, you do not have to do physical education. Thus, it is possible to remove worn-out rubber from the rims.
The disc diameter for the grinder is smaller and OK.
Do not cut with a jigsaw - longer.
A well-sharpened strong knife (in the sense the handle is thicker than a table knife). )
I made myself a container for water, I cut a balloon from K-700 with a knife quite successfully. And balloons from cars are generally easy. If only the cord is cut, then the metal of the knife.
Do not cut with a jigsaw - longer.
A well-sharpened strong knife (in the sense the handle is thicker than a table knife). You pierce the sidewall with a knife and forward a little wetting the knife in water (you can practice it, but then try not to freeze the handle of the knife - it will slide)
K-700 is quite successful. And balloons from cars are generally easy. If only the cord is cut, then the metal of the knife.
+1. I cut the sidewall with an ordinary table knife with salidol or lithol. the mother-in-law remained satisfied with the flower beds.
A sharp knife and lubricated with glycerin, you can use perfume — it glides like clockwork and then is easily washed off with water. The method is recommended in the Chemist's Handbook for cutting rubber stoppers, and they are very hard.
Thank you!
I realized that it's better with a knife!
I'll try today.
Ideal for cutting with vibroknife, with lubrication just do quickly, it is better to use silicone grease. Only if there is a metal cord, then the knife instantly becomes dull and stops cutting, metal cord only with a grinder
If for the purpose of cutting the tread - then with special tungsten staples - in the form of staplers and a special straightener .
.. ... the result - as from the factory ....
you need to ask the rally drivers, or even better, the autocrossers. somewhere I even saw for sale knives for cutting rubber.
If for the purpose of cutting the tread -
That's what I did 15 years ago. :) In the garage somewhere, there must still be a soldering iron tip with a U-shaped sharpened tip implanted in copper made of some kind of cool steel.
It is necessary to cut with a jigsaw, a rough saw, a grinder is much worse, it cuts more slowly and the stink is worth it, be healthy and the klzhukh will shit all at once. Checked;)
It is necessary to cut with a jigsaw, a rough file,
Thank you very much!
Moreover, it is a rough file with a large tooth. At first I tried with a metal file with a small tooth (I cut the tire along the tread, and there was a metal cord, so-so-so little wires :), but there are a lot of them :confused :). A metal file with a fine tooth cuts wires, things go slowly, the file quickly sits down.
And the file with a large tooth - it tears the wires, things are going much more fun. In order to strip the tire, it took 2 files with a large tooth and 10 minutes of time. Sticking wire tatters are perfectly polished together with rubber with a grinding (thick) grinder disc.
vBulletin® v3.8.11, Copyright ©2000-2018, Jelsoft Enterprises Ltd. How to change a tire
Sooner or later this should happen to most of everyone. You're driving with your mind through an important meeting agenda, and suddenly your car pulls to the side and you hear that terrifying flat tire popping sound.
Many drivers now have roadside assistance services that will fix your apartments, but it's always smart to know how to change apartments yourself. Since this is a fairly common occurrence, car manufacturers have tried to make the process of changing tires something that just about anyone can do.
Keep the following items in the vehicle for changing tires:
Spare wheel , Jack , Wrench and are vital and must be supplied with your vehicle. If any of these three are missing, replace them immediately with . Keep your vehicle owner's manual in your car at all times, as it will contain detailed information on where to find replacement parts and instructions for changing tires.
In case your tire blew while you were on the road, will slow down, , will turn on the hazard lights on , and will find a safe place to change your tire. If you are driving on a freeway or on a busy city street, It's best to drive as far away from traffic jams as possible.
Ideal tire change locations include:
If you can, try to get off on a flat road and not on a slope Also, changing tires on a paved road is ideal. If you cannot safely maneuver your vehicle in one of these areas, pull as far to the right as possible to increase the distance between your vehicle and traffic.
Once your vehicle is in a safe and stable area, parked with the parking brake applied , follow the steps below to replace a flat tire.
Once your spare vehicle is securely attached to your vehicle, will deliver the flat tire to the repair shop.
High speed driving is not recommended, so try to replace or repair a flat tire as soon as possible.
Changing your own tire can be a cost effective option if you don't have emergency roadside assistance. But safety should always be your top priority. Keep the following in mind when deciding whether to DIY or call for help.
Consider whether you can exit your vehicle in a safe place, away from oncoming traffic and onto a flat, level surface. If you are on a busy freeway, narrow shoulder, dirt road, slope, or slippery surface, think carefully before pulling out the jack.
If it is raining or snowing, if the wind is howling and you could lose control of any equipment, or if the blazing heat could endanger your health or safety, consider calling for a tow.
If you are traveling with family, friends or even pets, consider the environment and their safety.
If conditions are not ideal, play it safe to save a few dollars.
To ensure proper preparation, make sure your replacement material is inflated and in good condition. If you lack any other equipment, if your jack is rusty, even if your flashlight batteries are dead, don't try to be a hero - call a tow truck and get the help you need.
Knowing how to change a tire is an essential skill for all drivers. If you rely on your mobile phone to save you in a roadside emergency, there's always the possibility that you'll forget to charge it, be out of range, or leave it at home. Flat tires can happen anywhere, and a cell phone is no substitute for knowing how to change a flat tire.
Fortunately, changing a tire is not that difficult! Just stick to the following guidelines to be prepared if you have an apartment.
These items should have come with your vehicle:
Here are some items that are not included with your vehicle, but you should put them in the trunk or glove box in case you need to change a flat tire: 2"x6" wood cut to secure jack
As soon as you realize you have a flat tire, do not brake hard or turn. Reduce your speed slowly and scan the environment on a flat, straight road with a wide shoulder. An empty car park would be ideal. Flat ground is good because it will prevent your vehicle from moving. Also, straight sections of road are better than curves because oncoming traffic is more likely to see you.
Never attempt to change a tire on a narrow shoulder near oncoming traffic. Keep moving (slowly) until you find a safer spot. While driving on a flat road, you can ruin the rim, so replacing the rim is better than hitting an inattentive driver.
Be sure to consult your owner's manual for specific steps for replacing a flat tire on your vehicle.
Your hazard lights or flashers will help other drivers see you on the side of the road. To avoid an accident, turn them on as soon as you know you need to stop.
After stopping, always apply the parking brake in preparation for changing a flat tire. This will minimize the chance of your vehicle rolling over.
Wheel chocks are placed in front of or behind the tires to ensure the car will not roll while you fix the flat tire. If you are changing the rear tire, place it in front of the front tires. If you have a flat tire in the front, install wheel chocks behind the rear tires.
Bricks or large stones will work just as well as "real" wheel wedges. Just make sure they are big enough to stop the car.
.
If your vehicle has a cap that covers the lug nuts, it is easier to remove it before jacking up the vehicle. If your mounting nuts are exposed, you can skip to step 6.
Use the flat end of the wrench to remove the cap. This will work for most vehicles, but some hubcaps require a different tool. Refer to your owner's manual for the correct hubcap or wheel cap removal procedure.
Using the handpiece wrench, turn the handpiece nuts counterclockwise until you break their resistance. You may have to use force, and that's okay. Use your leg or full weight if necessary.
Loosen the clamp nuts about ¼-½ turn, but do not remove them completely yet. Save this for when it's time to remove the tire/wheel from the car.
The correct place for the jack is usually under the frame of the car next to the flat tire. Many car frames have molded plastic at the bottom with a cleared area of exposed metal specifically for jacking. To safely raise and avoid damaging your vehicle, follow the jack placement instructions in your vehicle owner's manual.
Place a small 2 x 6 inch piece of wood under the jack before attempting to raise the vehicle. This tactic is particularly useful on tarmac.
With the jack correctly positioned, raise the vehicle until the flat tire is about six inches above the ground.
Never place any part of your body under the vehicle during or after the vehicle has been jacked up.
Now it's time to completely remove the lug nuts. Since you have already loosened them, you should be able to unscrew them mostly by hand.
Grasping the tire by the treads, carefully pull it towards you until it is completely free of the hub behind it. Place it on its side so it does not roll.
Now place the spare on the hub, aligning the rim with the eyebolts. Gently press until the eyebolts are visible through the rim.
Install the flare nuts on the bolts and hand tighten them completely. Once they are all on, test each one again, tightening as much as possible. You will tighten them with a wrench after lowering the car to the ground.
Use a jack to lower the vehicle so that the spare wheel is on the ground and the full weight of the vehicle is not completely on the tire. At this point, you should tighten the nuts with a wrench, turning clockwise as much as possible. Click on the wrench with the full weight of your body.
Drive the vehicle to the ground and remove the jack. Tighten the mounting nuts again with a wrench until they are as tight as possible.
If the cap you removed from the flat tire fits your spare tire, replace it the same way you removed it originally. If it doesn't fit, put it away with the tire when you put away your equipment.
Here is a jack, wrench, wheel chocks, a flat tire and possibly a hubcap. Don't forget to put them all in your car before you leave.
You should check the tire pressure on the spare wheel to make sure it is safe. Type T Temporary Spare Parts, also referred to as "Mini Spare Parts", require 60 psi. Inch (420 kPa). If the tire needs pressure, drive immediately (slowly) to a service station.
Temporary spare tires are not designed to be driven long distances or at high speeds, so drive carefully until you can visit a tire repair technician. A professional should be able to determine if your tire needs service. repair or it's time to replace it.
