Home > Company > Tire Safety > Choosing Tires > Determining Tire Size
Once you have determined it’s time to buy tires, you’ll need to know what size tires are correct for your vehicle. Depending on what you drive, you may be interested in how to find the right tire for your…
This information is usually inside your car’s doorjamb, in your owner’s manual. To ensure your current tire or a replacement tire you may be looking at matches your vehicle’s requirements, it will be good for you to understand how tire sizing works. You may have never paid attention to the string of numbers and letters on every tire, but it’s a gold mine of information.
If you’re unsure of how to read tire measurements from your tire walls, the information and graphics below will tell you how to read tire size, understand and interpret it. If you decide you want to substitute a new size or tire type, consult an authorized tire retailer who can expertly advise you, because many optional tire sizes may have different load capacities and could require wheels of a different rim width or diameter and different inflation pressure.
Not sure you need new tires? Our Tire Replacement Guidance article will help you determine whether it’s time to retire your tires.
Most passenger cars, SUVs and light pickups (1/2 ton and smaller) will come with tires that are either P-Metric or Euro-Metric. For P-Metric tires, you’ll see the letter “P” before the number sequence begins: P225/70R16 97H. P-metric is a designation standardized by the Tire and Rim Association for a “passenger car” tire type. For Euro-Metric there will be no preceding letter before the number sequence begins: 225/70R16 98H. Euro-Metric is a designation standardized by the European Tyre and Rim Technical Organization for a “passenger car” tire type.
Both P-Metric and Euro-Metric size tires are designed to primarily be used on passenger vehicles, which can include cars, minivans, SUVs, and other light duty pickup trucks.
If your vehicle is an SUV, Pickup truck or van, you might see a different type of size designation on your placard that is specific for heavy duty light trucks and vans, especially common on ¾ ton and larger pickup trucks and vans. There are two common size types in this category, LT-Metric and Euro-Metric Commercial (aka C-type). Both size types are metric and so use the same structure as P-Metric and Euro-Metric but have some different characters in the size that differentiate them from their passenger car cousins. LT-Metric tires will have the letters “LT” before the size number sequence: LT245/75R17 119/116R Load Range E. Notice that there are two load index numbers and a Load Range, see the section on Load Index for more info. LT-Metric is a designation standardized by the Tire and Rim Association for a “light truck” type tire.
Euro-Metric Commercial or C-Type tires will look very similar to a passenger Euro-Metric size except that there will be a “C” right after the rim size: 23/65R16C 121/119R. Notice that the C-type tires also have two load index numbers. Euro-Metric Commercial, or C-Type is a designation standardized by the European Tyre and Rim Technical Organization for a light truck type tire. Light truck tires are designed to be used on vehicles capable of carrying heavy cargo and are usually only specified by a vehicle manufacturer on vehicles exceeding a certain load capacity.
Other types of tires that fall into the Metric sizing type are Temporary Spares, they start with “T”. If you see a size that starts with “ST,” that means “special trailer” and is only for use on a trailer.
Regardless of whether you are looking at a P-Metric, Euro-Metric, LT-Metric, Euro-Metric Commercial, T or ST tire the numbers in the size mean the same thing.
The first number to appear in your tire size information is the width, in millimeters, of the correct tires for your vehicle: P225/70R16 91S.
Tire width always refers to the measurement from one sidewall to another. Thus, a tire with the measurement “P225” is for a passenger vehicle and has a nominal width of 225 millimeters.
After the slash mark, the next number you see is for the tire’s aspect ratio, which essentially tells you how tall your tire’s profile is: P225/70R16 91S. Aspect ratios are delivered in percentages. Tire makers calculate the aspect ratio by dividing a tire’s height off the rim by its width. If a tire has an aspect ratio of 70, it means the tire’s height is 70% of its width.
Lower aspect ratio tires, such as a 60 series, generally offer vehicle handling performance advantages over higher aspect ratio tires, such as a 75 series, but a typical trade off can be ride harshness.
After the aspect ratio comes a letter that indicates the type of internal construction maintaining your tire’s stability: P225/70R16 91S.
There are two types of construction that you may see on the sidewall of a tire:
Radial tires are the most common tires on the road in the United States today; thus “R” will usually be shown in the tire size designation. Radial construction means the tire’s internal ply cords are oriented in a radial direction, from one bead over to the other, essentially perpendicular to the direction of rotation. You may also occasionally see RF indicating a run flat tire or ZR indicating a tire that is a speed rating higher than V.
The next number is the diameter code, in inches, of the rim onto which the tire can be mounted. For example, a tire with the P225/70R16 91S would fit a rim with a 16-inch diameter.
Load index can be a confusing subject because there are so many different caveats, but we will try to explain everything here.
The next figure after the rim size in the sequence is your tire’s load index, which tells us how much weight, in pounds, the tire can support when fully inflated: P225/70R16 91S
We call it the load “index” because the number doesn’t tell us the precise number of pounds the tire can carry, at least not by itself. However, the number does correspond to a specific load capacity listed in an index. Beginning with 1 and ending with 150, numbers in the load index represent carrying capacities of 99 to 7385 lbs.
There are two types of load types for passenger tires though, Standard Load and Extra Load. If a tire is Standard Load there will be no markings indicating it but if it is Extra Load the letters XL will appear after the size and load index.
Standard Load Euro-Metric: 215/55R17 94V
Extra Load Euro-Metric: 215/55R17 98V XL
Passenger car tires like P-Metric and Euro-Metric will only have one load index number where LT-Metric and Euro-Metric Commercial (C-Type) will have two numbers separated by a slash.
The first number is the load index if the tire is used in a single application, the second number is the load index if the tire is used in a dual application. Passenger type tires cannot be used in a dual application. Light truck tires will also have a Load Range that is indicated by a letter, such as Load Range E. Load Range is an older term that is still commonly used in the industry so you may hear your tire dealer reference it but the load index numbers are the best way to ensure you have the proper tire.
One important but often misunderstood facet about load index is that the load index numbers between standards organizations (P-Metric vs Euro-Metric) are not necessarily on the same scale. Meaning that two tires in the two different systems that have the same load index number could have different maximum load capacities. This is why it’s important to not only look at the load index number but also verify the actual load capacity.
The final figure in a tire size sequence is the speed rating, which is indicated by a letter: P225/70R16 91S.
Just as your load index number corresponds to a specific load, your speed rating letter corresponds to a particular speed capability based on a standardized laboratory test.
For example, a tire with speed rating “S” is rated for up to 112 mph, while a tire rated “R” is up to 106 mph. Remember that this isn’t a recommended cruising speed. Of course, you should always follow legal speed limits on roadways.
Replacement tires must have the same or higher speed rating as the vehicle’s Original Equipment to maintain vehicle speed capability. If a vehicle has tires with different speed ratings, it is the speed rating of the “slowest” tire that dictates the vehicle top speed.
There is one last sizing type that you should know about, especially if you are in the market for off road tires for a light truck or SUV. It’s called a Flotation size and the numbers in this sizing format are very different from the Metric formats.
Flotation sized tires are similar to LT-Metric tires in application except for a few important points. Number one, they cannot be used in dual applications and number two, an equivalent size tire may have different load capacity than its LT-Metric counterpart.
The first number in the Flotation tire size is the overall diameter in inches. Pretty straight forward.
The second number is the section width (sidewall to sidewall) measurement in inches. Again, fairly simple.
After the section width comes a letter that indicates the type of internal construction: 33X12.50R17LT 120Q.
This is the same as is found in the metric sizing systems.
There are two types of construction that you may see on the sidewall of a tire:
Radial tires are the most common tires on the road in the United States today; thus “R” will usually be shown in the tire size designation.
Radial construction means the tire’s internal ply cords are oriented in a radial direction, from one bead over to the other, essentially perpendicular to the direction of rotation.
The next number is the diameter code, in inches, of the rim onto which the tire can be mounted. For example, a tire with the 33X12.50R17LT 120Q would fit a rim with a 17-inch diameter.
The letters LT will be after the Rim Diameter indicating that this tire type is intended for Light Truck vehicles similar to the LT-Metric and Euro-Metric Commercial (C-Type) tires.
Load Index and Speed Rating have the same meaning and format as the tires using the metric sizing system. Note that since flotation tires cannot be used in a dual application there will be only one load index number instead of two.
Another group of stamping on certain types of tires is the Uniform Tire Quality Grading or UTQG. This grading and stamping is required for passenger car tires (i.e. P-metric and Euro-metric) in the all season and summer categories. Dedicated winter tires, Light Truck (LT-Metric, Euro-Metric Commercial, Flotation) and Motorcycle tires are excluded from this requirement.
Quality grading is designed to make the tire purchase decision easier for you. Ideally, the system is intended to provide simple, comparative data so you can make an intelligent buying decision. However, the ratings are based upon test results achieved under special conditions. This means it’s possible to misinterpret the comparative data as it relates to your individual driving habits, conditions, etc. You should still rely on your service or tire professional for assistance.
Quality grading designates the comparative performance levels of a tire based on government-specified tests but commissioned by the individual tire manufacturers.
All tire manufacturers are required to grade regular and all-season passenger tires in three categories:
UTQG
Treadwear
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course for 6,000 miles (9,600 km). For example, a tire graded 150 would wear one and a half times as well on the government course as a tire graded 100. However actual tire performance depends on driving habits, road characteristics, service practices, and other factors that can influence the outcome.
Traction Grades AA, A, B and C
The traction grades from highest to lowest are AA (the highest), A, B and C. They represent how well tires stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. C-rated tires will have the lowest traction performance.
WARNING: THE TRACTION GRADE ASSIGNED IS BASED ON A WET BRAKING (STRAIGHT AHEAD) TRACTION TEST AND DOES NOT INCLUDE CORNERING (TURNING) TRACTION.
Temperature Grades A, B and C
The temperature grades A, B, and C represent the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the tire’s material to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a performance level all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades A and B represent higher levels of performance on the laboratory test wheel than the minimum required by law.
WARNING: THE TEMPERATURE GRADE IS ESTABLISHED FOR A TIRE THAT IS PROPERLY INFLATED AND NOT OVERLOADED. EXCESSIVE SPEED, UNDER INFLATION, OR EXCESSIVE LOADING, EITHER SEPARATELY OR IN COMBINATION, CAN CAUSE HEAT BUILDUP AND POSSIBLE TIRE FAILURE.
DOT Quality Grades
All passenger car tires must conform to other federal requirements in addition to these grades.
Learn about our mission, our achievements, and our ongoing commitments
Read Our Origin Story
Tire size can be confusing. Some numbers on the sidewall are listed in millimeters while others are inches. Plus, the right size for your car, truck, or trailer can differ depending on where and how you drive.
You can see your original equipment tire size in your owner’s manual or on the placard generally located on the driver’s side door jam. This is the sizing recommended by the vehicle manufacturer.
If you’re interested in switching out your tires for a different look or performance, a good place to start is the numbers and other indicators on your existing tires’ sidewall. Next, have a tire professional help you determine a tire size range that will fit your vehicle and driving needs.
Here’s what those numbers and indicators on the sidewall indicate and how to understand them:
A: TIRE TYPE The first letter in the code tells you what class of tire it is.
P stands for passenger vehicle tire. P-class tires include cars, SUVs, crossovers, minivans and smaller pickup trucks.
LT means light truck tire, designed for vehicles that are capable of carrying heavy loads, towing trailers, or for those looking for an extra heavy duty option. These are often equipped on three-quarter or 1 ton trucks and SUVs.
ST stands for Special Trailer. These tire sizes are meant for trailers, including fifth wheels and other travel trailers, as well as boat and utility trailers.
If there’s no letter before the first number, you have a metric tire most commonly referred to as European size. It’s also measured in millimeters but may have a different load capacity than a P or LT tire.
B: TIRE WIDTH The three-digit number following the letter is the tire’s width (from side to side, looking at the tire head on) in millimeters. This may also be referred to as the section width.
C: ASPECT RATIO The forward slash separates the tire width number from the two-digit aspect ratio. The bigger the aspect ratio, the higher/taller the tire’s sidewall, or “profile” as it’s sometimes called.
The aspect ratio is indicated on the tire sidewall as a percentage. It’s the height of the sidewall measured from wheel rim to top of the tread, expressed as a percentage of tire width.
In this example, the aspect ratio is 65, meaning the sidewall is 65 percent as high as the tire is wide. To get the sidewall height, take the tire width of 215 mm and convert it to inches (8.46). Then multiply this by 65% (.65). This gives you an answer of 5.5, the sidewall height in inches.
D: CONSTRUCTION TYPE This single letter tells you about the internal construction of the tire.
R is for radial tires, the industry standard for most tires today. They have better road grip, lower rolling resistance for better gas mileage, ride comfort and durability than previous generations of tires. In a radial tire, the plies — layers of strong cords made of a blend of polyester, steel and fabric and coated with rubber — are laid perpendicular to the direction of travel.
D is for tires built with diagonal (crisscrossed) plies, called bias-constructed tires. They are also called conventional, x-ply, or cross-ply tires. Some motorcycle and trailer tires still use this internal construction.
Some run-flat tires are identified with an F followed by the type of internal construction.
E: WHEEL DIAMETER This two-digit number specifies wheel diameter in inches. It’s the distance between the two bead seat areas (where a tire gets tightly sealed onto the wheel).
F: LOAD INDEX The two-digit or three-digit number that follows the gap specifies tire load index.
The load index symbol indicates how much weight a tire can support, based on the following standard chart. In our example, the load index is 89, which indicates the tire has a load capacity of 1,279 pounds, when inflated to the tire’s maximum air pressure rating.
G: SPEED RATING The last letter is the tire speed rating. This indicates the top speed it’s safe to travel at for a sustained amount of time. A tire with a higher speed rating can handle heat better and provide more control at faster speeds. The maximum operating speed of a vehicle is no more than the lowest speed rating of all tires mounted on the vehicle. (Of course, you should always abide by speed limits for safer driving.) Speed rating is usually, but not always, a single letter (see the chart).
Below you will find several charts that will help you understand tire sizing numbers, including a load index chart and speed rating chart.
A tire size calculator is a quick way to see whether the tire size you’re considering will likely fit your car, SUV, sports car, light truck or crossover.
But remember that is only an estimate. It’s important to stay within the sizing tolerances of your vehicle. Tires that are the wrong size could cause some pull in the steering wheel, rub against the suspension or body of your vehicle, reduce clearance on hills, or result in a stiffer or noisier ride.
If you’re considering mounting a different tire size on your vehicle, check with a tire expert. Find out whether the tires and wheels you have your eye on are the right fit for your vehicle’s suspension, gearing, and bodywork. And ask how any differences in revolutions per mile, tire speed, load index, and speed rating will affect your ride quality and vehicle performance.
See how new tires and rims will look on your car or truck using our Virtual Wheels simulator, available at any Les Schwab.
Find Your Store
Choosing the right truck tires is essential to safe and trouble-free operation of your vehicle.
Therefore, it is necessary to know how the features of the marking and designation of rubber. This will help you understand the nuances and choose the most suitable set of wheels for current operating conditions.
Contents:
marking indicating the required parameters. In order to understand the specification of rubber, you should read the letters on the sidewall of the wheel, located around the entire circumference. The name and logo of the manufacturer, the brand of rubber, the direction of rotation of the wheel, and the dimension of the product are printed in large letters. nine0005
In the Russian market, in the marking of tires, European examples of dimension designation are most often found.
For example, the size 286*75*R15 is deciphered as follows:
As a rule, wheels for light vehicles are tubeless. This means that the rubber is simply put on the disc. Such products are labeled Tubeless. However, you can often find older models or domestically produced truck tires with TT (Tube Type) symbols. In the presence of this inscription, the tire is considered chambered.
nine0005
The cameras themselves also have their own symbols. Their decoding is very simple - the first number indicates the profile width in inches, and the two digits at the end indicate the bore diameter. There may also be symbols indicating the scope of the camera:
Keep in mind that tube tires require special rims for tubes. Therefore, attention should be paid to their designation. Signs LK, GK or RK are deciphered as: cars with a camera, trucks with a camera, adjustable tube tire. On the disks of this manufacturer, you can install chamber rubber. nine0003
Sometimes cargo kits are installed using rim tape. It consists of durable elastic rubber and is worn under the tire itself. This allows you to better protect the sidewall from abrasion and damage to the cord on the surface of the disc.
The tape has its own marking consisting of two numbers.
The first number is the band width and the second is the rim diameter. Sometimes two values are indicated in the marking of the rim tape for the wheel - in inches and millimeters for ease of use. nine0005
A complete list of compliance with the requirements of truck tires is described in GOST 5513-97. The document regulates all the standards for such tires and the required parameters. All markings must be on the outside. A height of 1.6 mm is the minimum indicator for a tire tread. When these indicators are reached, the kit must be replaced. Winter tires have completely different standards - here the critical number is 2.5 mm of residual tread height. nine0003
This document also regulates the ply rating of tires. Plying - the number of layers of cord on the sidewall of the rubber. For diagonal truck tires, the designation starts with 8 plies, and the maximum figure is 18. Radial wheels are more durable and modern.
Another important characteristic of truck tires is the maximum speed index at which you can continue driving. In the marking of truck tires, this indicator is indicated by the letter of the Latin alphabet. The closer it is to the end of the alphabet, the higher the speed category. Truck tires are produced with indices J, K, l, M, N, P, Q, R corresponding to speed indicators from 100 to 170 km/h in 10-point increments.
In addition to the speed category, the tire load index for SUVs and trucks is indicated. These two numbers are adjacent to the maximum speed indicator. The higher this indicator, the greater the maximum allowable load on each wheel. This parameter is calculated at the maximum allowable tire pressure (kPa). This indicator is indicated on the sidewall of the tire. nine0005
The minimum index for trucks is 119 for single wheels and 116 for twin wheels. If the letters EL or Reinforced are applied to the rubber, then this indicates a reinforced structure and an increased number of Radial layers.
This inscription indicates that the load capacity of the wheel is 3 units higher.
| Tire markings | |
|---|---|
| Index | Maximum wheel load |
| 116-120 | 1250-1400 |
| 121-130 | 1450-1900 |
| 131-140 | 1950-2500 |
| 141-150 | 2575-3350 |
| 151-160 | 3450-4500 |
| 161-170 | 4625-6000 |
| 171-180 | 6150-8000 |
| 181-190 | 8250-10600 |
There are two markings for American tires. The first one is very similar to the European one, only letters are added in front of the standard size indicating the scope of the product. For example, P 195 60 * R17, in addition to the profile height and landing diameter, says that the tire is installed on passenger cars (P - passanger), and the letters LT or T indicate the cargo direction (Light Track, Track).
The second way to label light truck tires uses a different approach and inch system. If there are numbers on the product, for example, 30 * 10 * R16, then 30 is the outer diameter of the tire in inches, 10 is the tread width, and 16 is the diameter of the inner rim. nine0005
Sometimes there are color markings on the tire. This means that there are reinforced places in the tire design. These inhomogeneities are completely normal and are designed to facilitate editing on the disc and achieve balance.
The yellow triangle indicates the heaviest part of the tyre. Such a mark must be aligned with the letter L on the stamped disc itself.
The red dot marks the stiffest part of the wall and aligns with the same mark on the alloy wheel. Colored stripes or a white stamp with a number may also be present. The first ones help to find the necessary kit in the warehouse, and the second one gives information about the number of the inspector at the factory who evaluates the kit.
nine0005
Some manufacturers add additional markings to their products. The production date is very common. It is expressed in four digits. The first indicate the serial number of the week, and the last two indicate the year of production. The date of manufacture with the following figures 1710 is the 17th week of the 10th year.
You can often see the sign Outside. Such rubber has an asymmetric tread pattern, and the badge should be directed outward. This will ensure that the kit behaves correctly under all conditions. If there is no such inscription on the sidewall of the tire, then it can be installed on any axle by any side. nine0003
Standard kits are designed for safe driving on normal surfaces. If you need improved cross-country performance, then you should take a set of size M + S. If these characters are deciphered for trucks, then they stand for Mud + Snow. Such wheels are considered all-weather and can provide good cross-country performance even when driving on muddy or snowy roads.
New Cars > Tires >
The right choice of truck tires is the key to safe, comfortable and long-term operation of vehicles. Thanks to the correct selection of tires, the following characteristics of a truck can be significantly improved: braking properties, acceleration dynamics, fuel consumption, handling, stability, etc. That is why tires are clearly classified by different types and sizes and are marked.
Classification of tires occurs according to:
Tires for special equipment are allocated in a separate group: construction, mining, for truck cranes, excavators, loaders. nine0005
Chamber models consist of a chamber and a tire. The chamber has a valve. The rubber for the camera is flexible, airtight, resistant to temperature extremes and heat aging.
The size of the chamber must match the size of the tire. Tubeless has an additional sealing layer. Also, tightness is achieved by a very tight fit of the tire on the rim. The main advantage of such tires is that in the event of a puncture, the pressure is maintained for a long time, which entails additional guarantees for driving safety. nine0005
Bias tires have carcass cords crossed in adjacent plies. The angle of inclination of the threads in the middle of the tire is in the range of 45 - 60 degrees. Such tires are characterized by sidewall resistance to damage and a lower price. In radial tires, the carcass cords run parallel from bead to bead. The breaker cord threads run similarly to diagonal ones, but at a greater angle. Radial tires have a carcass with fewer plies, but with a stronger breaker, so they deform less when rolling, the tread slips less on the road. nine0005
Radial tire provides excellent handling, better lateral stability of the car, provides better traction due to a larger contact patch.
Summer tires are distinguished by pronounced longitudinal grooves for water drainage and a rounded transition from the tread to the sidewalls. This design provides better grip on dry roads and in the rain and is adapted for faster riding.
Winter tires are used on icy or snowy roads. The tread pattern has clearly defined checkers with a complex relief to increase the side surfaces and a branched micro-pattern. On many winter models, anti-skid studs can be installed to provide more reliable contact with the road. All-season tires are well used both on dry and wet pavement, they work satisfactorily on winter roads. Their tread pattern is more branched, the checkers are grouped into a track and separated by grooves: there is an additional micro-pattern on the checkers. nine0005
Tire manufacturers around the world adhere to a single standard, for Europe it is ETRTO. The basic size of truck tires includes the following characteristics:
The tire series is the ratio of profile height to profile width in percent.
Marking of truck tires of radial type on the example of 10.00R20 146/143 (all values are given in inches) stands for:
In addition, manufacturers can mark their products and other designations:
| Index | load, kg | Index | 9009 | Load kg | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 62 | 265 | 95 | 690 | 128 | 1800 | nine0102 1614625 | |||||
| 63 | 272 | 96 | 710 | 129 | 1850 | 162 | 4750 | ||||
| 64 | 280 | 97 | 730 | 130 | 1900 | 163 | 4875 | ||||
| 65 | 290 | nine0102 98750 | 131 | 1950 | 164 | 5000 | |||||
| 66 | 300 | 99 | 775 | 132 | 2000 | 165 | 5150 | ||||
| 67 | 307 | 100 | 800 | 133 | 2060 | 166 | nine0102 5300|||||
| 68 | 315 | 101 | 825 | 134 | 2120 | 167 | 5450 | ||||
| 69 | 325 | 102 | 850 | 135 | 2180 | 168 | 5600 | ||||
| 70 | 335 | 103 | nine0102 875136 | 2240 | 169 | 5800 | |||||
| 71 | 345 | 104 | 900 | 137 | 2300 | 170 | 6000 | ||||
| 72 | 355 | 105 | 925 | 138 | 2360 | 171 | 6150 | ||||
| 73 | 365 | 106 | 950 | 139 | 2430 | 172 | 6300 | ||||
| 74 | 375 | 107 | 975 | 140 | 2500 | 173 | 6500 | ||||
| 75 | 387 | 108 | 1000 | 141 | 2575 | 174 | 6700 | ||||
| 76 | 400 | 109 | 1030 | 142 | 2650 | 175 | 6900 | ||||
| 77 | 412 | 110 | 1060 | 143 | 2725 | 176 | 7100 | nine0098||||
| 78 | 425 | 111 | 1090 | 144 | 2800 | 177 | 7300 | ||||
| 79 | 437 | 112 | 1120 | 145 | 2900 | 178 | 7500 | ||||
| 80 | 450 | 113 | 1150 | nine0102 1463000 | 179 | 7750 | |||||
| 81 | 462 | 114 | 1180 | 147 | 3075 | 180 | 8000 | ||||
| 82 | 475 | 115 | 1215 | 148 | 3150 | 181 | 8250 | ||||
| 83 | 487 | 116 | 1250 | 149 | 3250 | 182 | 8500 | ||||
| 84 | 500 | 117 | 1285 | 150 | 3350 | 183 | 8750 | ||||
| 85 | 515 | 118 | 1320 | 151 | 3450 | 184 | 9000 | ||||
| 86 | 530 | 119 | 1360 | 152 | 3550 | 185 | 9250 | ||||
| 87 | 545 | 120 | 1400 | 153 | 3650 | 186 | 9500 | ||||
| 88 | 560 | 121 | 1450 | 154 | 3750 | 187 | 9750 | ||||
| 89 | 580 | 122 | 1500 | 155 | 3875 | 188 | 10000 | ||||
| 90 | 600 | 123 | 1550 | 156 | nine0102 4000189 | 10300 | |||||
| 91 | 615 | 124 | 1600 | 157 | 4125 | 190 | 10600 | ||||
| 92 | 630 | 125 | 1650 | 158 | 4250 | 191 | 10900 | nine0098||||
| 93 | 650 | 126 | 1700 | 159 | 4375 | 192 | 11200 | ||||
| 94 | 670 | 127 | 1750 | 160 | 4500 | 193 | 11500 |
64400 p
Yokohama 425/65 R22.
