How to reset the service tire monitor system

How to Reset Your Tire Pressure Light

Skip to main content

Hide Show

Sell/Trade Us Your Car | Click Here To Learn More

Your tire pressure light provides a critical reminder to restore the pressure in your vehicle's tires when it gets low. You should only attempt to reset the light after first addressing the tire pressure in every tire. Once your tires are at the appropriate pressure, the light may go off on its own. If it doesn't go off right away, driving at 50 mph for about 10 minutes should help the tire pressure sensor reset.

If the tire pressure light is still on, there are a few more tricks you can try:

  • Turn the car key to "on" but don't start the vehicle. Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off within 20 minutes.
  • Disconnect the positive battery cable while the vehicle is off. Turn the car on and press the horn for three seconds to discharge the remaining power. When you reconnect the battery the tire pressure light should be off.
  • Overinflate all the tires (including the spare) with 3 PSI, then deflate them completely. Re-inflate the tires to help reset the light.
  • Bring your vehicle to our service center for professional assistance.

IS TPMS the Same as Tire Pressure Light?

Image via Unsplash by introspectivedsgn.

 TPMS stands for Tire Pressure Monitoring System. The tire pressure light is one component of this electronic system, providing a visual alert when your tire pressure is low. The TPMS monitors tire pressure using either an indirect or direct method.

An indirect TPMS measures the rate of revolution for each wheel. If a wheel starts spinning faster than anticipated, the system signals to your vehicle's computer that something is amiss with the tire rotation, and your tire pressure light comes on. You must manually reset the monitor in an indirect TPMS system.

A direct TPMS uses pressure monitoring sensors in each tire to monitor tire pressure exactly. This is a more accurate alternative to an indirect TPMS system. The batteries inside these sensors will last for about 10 years. Direct TPMS systems reset automatically after tire inflation or rotation. You do need to have these sensors resynchronized when you get new tires, which requires a special tool.

Can Cold Weather Cause Your Tire Pressure Light to Go On?

Yes, cold weather will affect the air pressure in your tires. Your tires lose one or two pounds per square inch (PSI) for every 10 degrees that the temperature drops. Cold air condenses while warm air expands. Therefore, the colder air in your tires will take up less space in lower temperatures.

You may find that your TPMS light is only illuminated for a short time in the morning on particularly cold days. After about 20 minutes of driving, the air will often warm up and expand, restoring proper pressure in your tires. If the light stays on after 20 minutes on the road, you should add air to your tires as needed to restore the proper pressure. Low tire pressure is hazardous for your vehicle regardless of the cause.

Why Is My Tire Pressure Monitor Light On When My Tires Are Fine?

When the tire pressure monitor light is on, the first thing you should do is check the pressure in each of your tires, including the spare. Check the manufacturer's recommendation to determine the appropriate pressure for each tire. This is typically between 30 and 35 PSI but may vary. You should measure tire pressure when the tires are cold, which means they have not been driven in the last three hours.

To check the pressure, simply unscrew the valve cap and insert a tire gauge into the valve stem. The gauge will provide a clear reading. Replace the valve cap when you're finished. If your tires are all at the appropriate pressure, there's a malfunction with your TPMS. Bring your vehicle to an authorized dealership service center to diagnose and resolve the issue.

Is it OK to Drive With My Tire Pressure Monitor Light On?

If the tire pressure monitor light is on, you should check your tire pressure as soon as possible. Low tire pressure creates a serious hazard on the road. According to the National Highway Traffic Safety Administration, 738 people died in tire-related crashes in 2017. When tire pressure is low, the tire has more contact with the road. This may cause the tire to overheat, leading to tread separation, excessive tire wear, or a blowout.

Low tire pressure also wreaks havoc on your fuel efficiency. You can save up to 11 cents per gallon simply by keeping your tires properly inflated. You'll also save money on tire replacements with adequate inflation. Keeping your tires properly inflated can add 4,700 miles to the tire's average lifespan.

The tire pressure monitor light gives you valuable information and should not be ignored.

Do I Need to Replace My TPMS When I Get New Tires?

You do not necessarily need to have your TPMS sensors replaced with new tires, but this is a good time to check them and make sure they're still in good condition. If you have an indirect TPMS system, your mechanic will need to manually reset the sensors after changing your tires. If you have a direct TPMS system, no additional maintenance is required to reset the system.

A new TPMS system will typically last for about 10 years before the batteries run out. If you have an older vehicle, you may need new sensors every five or six years. Your mechanic can advise you on the best time to replace TPMS sensors for your vehicle. When new sensors are installed, the system must relearn the location of each tire, which requires a detailed series of technical procedures. You should leave this task to a professional. 

If you need tire service for your Toyota, come to Kings Toyota for prompt, reliable service. Our highly-trained technicians are equipped to assist with any type of tire issue, whether you need new tires or have a malfunctioning tire pressure sensor light. Make your appointment today.

Make an Inquiry

* Indicates a required field

First Name*

Last Name*

Contact Me by*


How do you fix the service tire monitor system?

No matter how many times I check, empty, and refill the air in my tires, the service tire monitor system still thinks the tire pressure is low. Is there a way I can fix my tire monitor system?

Jack Walsh · Answered on Jan 27, 2022

Reviewed by Shannon Martin, Licensed Insurance Agent.

Constantly assuming your tire pressure is low must be stressful! Thankfully, there are easy ways to fix your service tire monitor system.

The easiest way to fix the service tire monitor system in your car is to reset the system. Occasionally, the sensors need some extra help, and you can reset the system using two different methods.

The first way to reset the system is by driving around at highway speeds for at least 10 minutes. The light should go away during your drive or the next time you start the vehicle.

If the above method doesn’t work, you should reset the TPMS light which can be done by:

  1. Turning the ignition to the on position without starting the engine.
  2. Locating the TPMS button and holding it down until the alert flashes or disappears.
  3. Driving around for a few minutes, turning off the car, and then restarting the engine.

If neither of the above methods works, you should visit a mechanic or dealership to have the service tire monitor system serviced by a professional.

If you’re looking for a way to pass the time while waiting for the mechanic to finish the repairs, you should download Jerry to save on your car insurance. A licensed broker that offers end-to-end support, the Jerry app gathers affordable quotes, helps you switch plans, and will even help you cancel your old policy once you’ve made a selection.

MORE: How to decide if you should take your car to a repair shop or a mobile mechanic

Car MaintenanceCar Tires

View full answer 


Jerry partners with more than 50 insurance companies, but our content is independently researched, written, and fact-checked by our team of editors and agents. We aren’t paid for reviews or other content.

Browse More Content

Car Repair Resources
    Insurance for Your Car
    • Mercury Tracer Base Insurance Cost

    • Audi A3 E-Tron Premium Plus Insurance Cost

    • Nissan Pathfinder Sl Insurance Cost

    • Chevrolet Venture Insurance Cost

    • Subaru Impreza Outback Sport Insurance Cost

    Insurance in Your State
      Insurance In Your City
      • Coral Gables Car Insurance

      • Broomall Car Insurance

      • Exton Car Insurance

      • Dacono Car Insurance

      • Franklin Car Insurance

      What Others Are Asking
      How do you deal with rain on your driving test day?

      I’m scheduled to take my driving test tomorrow, but it’s supposed to rain. I don’t really want to postpone it since it took so long for me to finally get an appointment, but I’m nervous. What should you do if it rains during your driving test?

      Michelle Ballestrasse

      Jan 27, 2022

      Is it illegal to eat or drink while driving?

      I’m going on a solo road trip soon, and I want to be as efficient as possible. Can I eat and drink while driving?

      Olivia Rose

      Jan 27, 2022

      How do you charge a maintenance free car battery?

      I haven’t used my car in a while, and when I went to start it, the battery was dead. How can I charge a maintenance free car battery?

      Jack Walsh

      Jan 27, 2022

      Browse All Questions

      Read Advice From Car Experts At Jerry

      Do You Need Motorcycle Insurance in Texas?

      Insurance requirements for motorcyclists in Texas are the same as those for car drivers—but what happens if you’re in an accident without the proper coverage?

      Sarah Gray

      Mar 01, 2023

      How to Get a Nevada Learner’s Permit

      You’re eligible to get a Nevada learner’s permit when you’re 15 and a half years old—but you’ll need to get your ducks in a row first. Learn more here.

      Macy Fouse

      Feb 24, 2023

      Are Two-Seater Coupes Cheaper to Insure Than Sedans?

      Two-door and especially two-seater cars are often more expensive to insure than four-door sedans. Read on to find out why.

      Sarah Gray

      Mar 23, 2023

      Browse By Topics

      Uninsured Motorist Protection

      Hail Damage

      VIN Lookup

      driving record

      Homeowners insurance

      21st Century

      Valuable Articles Insurance

      Liability insurance

      Loan Discounts

      Car Wash

      Car Buying

      State Farm


      Auto insurance

      Wear and Tear


      Rental Discounts

      Car Dealers

      Bodily Injury


      State Insurance Minimums

      Home and Auto Insurance

      negligent driving


      Driver's Permits

      Night Driving

      Reckless Driving

      Emergency Brakes

      Car Seats

      No long forms

      No spam or unwanted phone calls

      Quotes from top insurance companies

      Find insurance savings — it's 100% free

      Car Insurance by Make







      Car Insurance by State

      How to reset a tire pressure error: a few easy ways

      Save article:

      The article says:

      1. Why you need a tire pressure sensor
      2. What are the reasons for triggering the sensor
      3. How can I reset the tire pressure sensor error
      4. How to adjust tire pressure sensors

      When the tires are optimally inflated, the low tire pressure indicator (TPMS) does not light up on the vehicle's dashboard. However, in some cases, it lights up even if the pressure is normal. This can't help but be annoying, especially when the tires are inflated normally. In our article today, we will figure out how to reset a tire pressure error.

      Why do you need a tire pressure sensor

      American and European scientists conducted a study, during which it was found that most drivers do not check whether the wheels are properly inflated before getting behind the wheel of a car. Only 40% of car owners perform such a check - and even then only once every 12 months. This is the reason for a large number of accidents.

      The TPMS (Tyre pressure monitoring system) system is designed to monitor tire pressure, as well as warn of a malfunction. If the tires are under-inflated or over-inflated, an error will be displayed on the remote control or an audible signal will appear.

      What is dangerous too high or, conversely, low pressure? The risk of an accident increases, the car begins to consume more fuel, in addition, the rubber wears out faster.

      Photo: Shutterstock

      The above devices operate on the same principle. Let's figure out how information about what tire pressure gets to the control panel.

      • Each wheel is equipped with a controller. It records tire pressure data.
      • Information is transmitted from the sensor to the transceiver with a frequency of 2-3 seconds . The controller transmits data using Bluetooth.
      • The program analyzes the received data, which should correspond to normal values ​​ . Otherwise, when the tires should be lowered a little, the program sends a signal to the car owner. Exactly according to the same principle, a signal is transmitted if the rubber needs to be pumped up.
      • Depending on the device, the error signals are sound, as well as light .
      • The driver can set the operating parameter limit himself . As a standard, the automaker makes it possible to adjust the device from 1.7–3. 2 bar.
      • On some car models, the TPMS system sends data to your phone.

      Consider how pressure is calculated by measuring instruments. Typically, the sensor performs a comparison of the angular rotation of the wheel. Knowing the value of this parameter, you can calculate the distance that the wheel will travel in one rotation.

      Obviously, if the tires are under-inflated or over-inflated, then the outer diameter of the wheel will be different. Visually, a person cannot determine this change. But the sensor notices even such changes. The system fixes non-compliance with the required parameters.

      Causes of tire pressure sensor activation

      The sensor will still respond, despite the fact that the wheel circumference has changed quite a bit. In this situation, it is necessary to find out what mechanical reason led to this. Only in this way can you eliminate the misinterpretation of the signals transmitted by the system. This can happen because:

      • tire is under-inflated;
      • you have installed a different wheel whose shape, dimensions and tread are different;
      • was supplied with a "spare wheel", in terms of parameters it also differs from other wheels;
      • there was a puncture or rupture of rubber;
      • there is an uneven load on the car, as a result, the car skewed to one side;
      • you have installed anti-skid chains on the wheels;
      • one of the axes has been overloaded; this happens when you are driving uphill or downhill, towing a trailer.

      Also, the TPMS system gives an error when you install new wheels or rearrange them.

      When, after these steps, a tire pressure error appeared, indicating unbalance, you should reset the settings, and then set the basic parameters. In this case, the control signal may remain even if the basic settings have been selected.

      Why such problems may occur:

      • different tire pressures . Some wheel is under-inflated or vice versa;
      • The error occurs because the system has crashed . It will only be possible to reset it at the service station;
      • the indicator lights up when you operate the car using a sporty driving style, driving on ice, a dirt road . At the same time, as soon as you drive out onto an asphalt surface or start driving calmly, the error disappears.

      See also

      Velcro or spikes: which rubber is better for the Russian winter?

      Read more

      How to reset tire pressure error? To begin with, imagine that the TPMS system is working properly and the blinking light indicates a problem with the undercarriage of the machine. The first thing you should do is slowly release the gas. You can not brake sharply, turn the steering wheel. After the car has stopped, inspect the tires to make sure the rubber is not punctured or broken. Then you can check if the tire pressure is normal.

      Pay attention! The TPMS will not always show a tire pressure error. For example, if the tires are slowly deflating, the system will not inform you about the problem. In the same way, she will not notice the error if the tire pressure starts to drop rapidly. This usually happens when a tire ruptures. This feature of the TPMS system is explained by the specifics of identifying and counting nonconformities.

      However, in some cases, it happens that the TPMS system indicator is on, but the tires are in perfect condition. How to reset tire pressure error? We understand.

      A few simple ways to reset the tire pressure sensor error

      The complex TPMS system in some cases starts to work incorrectly. Usually, car owners observe the following picture: a tire pressure error is displayed on the display (the tire is underinflated), but in reality everything is fine with the wheel. You have to reset the tire pressure error. Otherwise, the TPMS system starts to work incorrectly.

      Photo: Shutterstock

      You also have to reset the tire pressure error when there is radio interference from high voltage power lines. Or when sources of radio signals are located in the immediate vicinity. But as soon as you move away from them, the pressure error disappears and the system begins to function properly.

      The reason for the malfunction may lie in the sensor, which is "failed". This damage cannot be easily repaired. How to reset a tire pressure error if the sensor flashes, while you hear a beep, lose your vigilance and find it difficult to drive a car? There are 4 ways to fix this problem.

      Method 1

      To reset the error, pick up a speed of 80 km / h and continue driving for another 15 kilometers.

      This method is the easiest to implement. If your car has this feature, then turn on the cruise control so that the speed does not change. Depending on the model of your car, you will be able to reset the tire pressure error at a speed that exceeds the specified one. After you cover a distance of 15-20 kilometers, maintaining the same speed of 80 km / h, make a stop. Turn off the motor. When you start it again, the tire pressure error will disappear.

      Popular articles

      How to choose a subwoofer for your car



      From top to bottom, obliquely: how to degrease a car body before painting



      Chic, shine, beauty: how to remove scratches on a car with your own hands

      9. 12.2022


      Without damage: how to reduce the fuel consumption of your car



      How much do they pay for advertising on a car



      Method 2

      Press the tire pressure monitoring system (TPMS) reset button on your car and you will be able to reset the error.

      It does not matter what type of low pressure warning system is used. In any case, there will be a sensor on each wheel of your car. Sometimes it may be necessary to reboot the touch system of the car. Read the owner's manual for the vehicle. It contains information on how to reset a tire pressure error. Most often, the instructions indicate which button to press to reset.

      The ignition key must be in the lock. No need to start the car, just turn it to the “on” (“ON”) position. Then press and hold the reset button, which may be under the steering wheel. We are waiting for the low pressure indicator to blink 3 times. After that, you can release the button. We start the car, it should work for 20 minutes. After this time, the computer will calibrate the sensors on the wheels. Now you can turn off the car.

      Method 3

      Lower and then re-inflate the wheels.

      Failed to reset tire pressure error using the previous method? Then we inflate all tires to 0.2 bar, this is the pressure that should be according to the recommendations of car manufacturers. Did the error go away? Then we lower the pressure in the tires completely.

      Now we pump up the wheels again. The pressure in them should be the same as indicated on the driver's door pillar or in the car's operating instructions. When there are sensors on the wheels, you need to remember about the spare tire. Now you need to drive about 3-5 kilometers, adhering to a speed of 25 km per hour. So you can reset the tire pressure error.

      Method 4

      Remove the battery terminals and then connect it to reset the error.

      Each car has a computer that receives data from all kinds of vehicle sensors, including TPMS system sensors. However, any electronics can fail. To reset the error, you will have to reboot the system, for which you need to turn off the power.

      Photo: Shutterstock

      To do this, open the hood. The battery is located under the hood. Disconnect the negative terminal from it. To perform this operation, use a wrench. Then sit in the driver's seat, turn the key to the "ON" position, but do not start the car. Now you need to press the signal for 3 seconds. This will use up the energy that remains in the electrical system of the machine. Then reconnect the battery. This way you can reset the error.

      How to adjust the tire pressure sensors

      Sensors keep track of tire pressure. However, you need to be sure that they function properly. Of course, you do not need to constantly walk around with a special measuring device and find out the status of the sensors. It just needs to be calibrated from time to time.

      It is performed quite simply. The most important thing to remember is that, depending on the make and model of your car, for each wheel there are pressure parameters strictly defined by the manufacturer for winter and summer. These values ​​should be given to the sensors. How the installation and configuration will be performed depends on the controller used.

      • Mechanical controller . It is convenient to use. We just screw it in instead of the cap. Nothing else needs to be configured.
      • Electronic controller . The installation procedure will be more difficult, because the device has a control unit. It can work autonomously or you will need to connect it to the cigarette lighter. We turn on the device in the training mode. Then proceed according to the tuning algorithm that is set by the manufacturer. You will have to put the device on all wheels, starting from the left front. Once the installation is done, make sure that all gauges are correctly displayed on the monitor. Otherwise, you will have to rearrange them so that everything matches the parameters on the display.
      • Internal controller . Such devices are the most difficult to mount, because for this you will have to use special equipment for tire fitting. Experts do not recommend using the internal controller yourself. However, additional settings are not required if the data is read using the screen that is directly on the control system.

      For current promotions on the Halva card, which will help you profitably purchase household appliances, you can follow here.

      To prevent a tire pressure error from appearing, it is important to calibrate (adjust the TPMS system) every time a change is made. For example, when you installed a new set of wheels, repaired tires, did balancing, and the like. Using TPMS controllers is quite simple. The main thing is to read the instructions for use of the device. And make sure that the tire pressure is the one recommended by the car manufacturer.

      See also

      "What tires can be put on rims 14, 15 and 16: professional advice"

      Read more

      Every car owner gets annoyed if the tire pressure error icon lights up on the dashboard. This indicator informs you that something is wrong with the wheels. However, even if the tire pressure is optimal, the tire pressure error must be reset.

      The fact is that if the TPMS system icon constantly signals insufficient pressure, the driver will not be able to know when the rubber will actually begin to deflate. Driving becomes dangerous for both you and other road users. It is necessary to find out the cause of the malfunction as soon as possible and reset the tire pressure error. This is the only way to operate the vehicle safely.

      Hyundai Creta tire pressure error: detailed instructions

    • Recommendations
    • Questions

    Hyundai Creta tires are a common nuisance for Korean crossover owners. The problem lies in the low accuracy of the device.

    Its error can reach 30%, that is, about a third of the system operations, an error. While half of the drivers have come to terms with the imperfections of their beloved SUV, the other half are desperately trying to fix it, bumping into an insurmountable obstacle.

    The fact is that it is impossible to turn off the sensors. We'll have to look for other ways to remedy the situation. What exactly? Now we'll tell you.

    How to reset a TPMS error

    The most obvious way to reset a tire pressure sensor error is to check the condition of the tires. Yes, the error in the operation of devices is extremely high, but in most cases they still signal a real problem.

    If the insidious light comes on while driving, stop at a convenient authorized place and make sure the tire is properly inflated. To do this, it is better to use a pressure gauge, because it is not so easy to determine by eye where the air is released.

    Then proceed according to the situation. Try inflating the tire to the standard level, and then start the car and drive at normal speed for several kilometers.

    Hyundai Creta tire pressure error will reset itself, without requiring additional expert intervention. The miracle did not happen, or was the tire completely in order, but the light continues to burn, distracting and annoying? Then you have to be cunning and here are the main ways:

    • Try to go to the track and move along it at the same speed for an hour. The fact is that the sensors installed in the Korean crossover function only on the go, and sometimes it takes time to receive an adequate signal from the disks to the head unit.
    • If there is no time for a “journey”, you can actually try to deflate the tire and then pump it up to the standard rate. Then you have to reset the error in the original way, after driving a few kilometers.
    • Didn't that help too? Then reboot your device. Remove the battery terminals for a couple of minutes, and then put them back in place.

    Important note: If you decide to remove the sensors from the discs, in the hope of getting rid of a regular error, then you will not come to the desired result. The light will remain on even if there are no devices.


    There is another way to disable TPMS on your Hyundai Creta. Experts call it initialization and it is mainly used when changing wheels between seasons. Proceed step by step:

    1. Switch on the ignition, but do not start the engine.
    2. In this state, hold down the SET button. You will find it on the left side of the steering wheel.
    3. Wait for a beep to confirm that the initialization procedure is complete.

    If none of the above methods helped, the light remains on, and you are absolutely sure that the tire pressure is at the level recommended by the manufacturer, you will have to go to a service center.

    There, using special software and a scanner, the master will be able to forcibly shut down the system or reflash it in order to finally rid the driver of the problem.

    Important note: Even a specialist in the service center does not turn off the tire pressure sensors. He only makes sure that the annoying signal on the dashboard does not turn on.


    Sometimes a frequent error may indicate that the device itself is broken. In this case, resetting errors on the Hyundai Creta will not help, because it will not fix the breakdown. Try changing the TPMS to a new one. You can do it yourself, but you will have to tinker.

    The tire pressure sensors in the Korean crossover are hidden directly inside the wheels, in the tire cavity. So for replacement, you will have to dismantle each of them.

    The best option would be to contact a specialized service center, but if you prefer to handle it yourself, then at least call a friend to help you, who will hold the disk.

    But there is no need to register new devices after their installation. Just drive a few kilometers at the same speed and the information will begin to be transmitted to the head unit.

    At the same time, no one will guarantee that beginners will not start making mistakes and you will not have to reset the Hyundai Creta tire pressure sensor. After all, you remember about the 30 percent error?

    However, we do not recommend trying to disable the pressure control. Better try to get used to it. Factory-installed sensors on the Hyundai Creta are one of the basic security systems designed to protect against accidents, rapid tire wear and other troubles.


    Vladimir, 55 years old (Yaroslavl)

    What standard pressure does the manufacturer provide for Hyundai Creta and does it depend on the type of engine?

    This indicator does not depend on the vehicle equipment. In a normally loaded car, tire pressure should be 2.3 bar, and in crossovers with a maximum load, 2.5 bar. The manufacturer's recommendations are displayed on a sticker located on the front of the driver's door. You can verify this for yourself.

    Sergey, 29 years old (Abakan)

    How does the level of tire pressure depend on weather conditions? I noticed that the malfunction from the sensors pops up only in the winter period.

    Learn more