Tire size can be confusing. Some numbers on the sidewall are listed in millimeters while others are inches. Plus, the right size for your car, truck, or trailer can differ depending on where and how you drive.
You can see your original equipment tire size in your owner’s manual or on the placard generally located on the driver’s side door jam. This is the sizing recommended by the vehicle manufacturer.
If you’re interested in switching out your tires for a different look or performance, a good place to start is the numbers and other indicators on your existing tires’ sidewall. Next, have a tire professional help you determine a tire size range that will fit your vehicle and driving needs.
Here’s what those numbers and indicators on the sidewall indicate and how to understand them:
A: TIRE TYPE The first letter in the code tells you what class of tire it is.
P stands for passenger vehicle tire. P-class tires include cars, SUVs, crossovers, minivans and smaller pickup trucks.
LT means light truck tire, designed for vehicles that are capable of carrying heavy loads, towing trailers, or for those looking for an extra heavy duty option. These are often equipped on three-quarter or 1 ton trucks and SUVs.
ST stands for Special Trailer. These tire sizes are meant for trailers, including fifth wheels and other travel trailers, as well as boat and utility trailers.
If there’s no letter before the first number, you have a metric tire most commonly referred to as European size. It’s also measured in millimeters but may have a different load capacity than a P or LT tire.
B: TIRE WIDTH The three-digit number following the letter is the tire’s width (from side to side, looking at the tire head on) in millimeters. This may also be referred to as the section width.
C: ASPECT RATIO The forward slash separates the tire width number from the two-digit aspect ratio. The bigger the aspect ratio, the higher/taller the tire’s sidewall, or “profile” as it’s sometimes called.
The aspect ratio is indicated on the tire sidewall as a percentage. It’s the height of the sidewall measured from wheel rim to top of the tread, expressed as a percentage of tire width.
In this example, the aspect ratio is 65, meaning the sidewall is 65 percent as high as the tire is wide. To get the sidewall height, take the tire width of 215 mm and convert it to inches (8.46). Then multiply this by 65% (.65). This gives you an answer of 5.5, the sidewall height in inches.
D: CONSTRUCTION TYPE This single letter tells you about the internal construction of the tire.
R is for radial tires, the industry standard for most tires today. They have better road grip, lower rolling resistance for better gas mileage, ride comfort and durability than previous generations of tires.
In a radial tire, the plies — layers of strong cords made of a blend of polyester, steel and fabric and coated with rubber — are laid perpendicular to the direction of travel.
D is for tires built with diagonal (crisscrossed) plies, called bias-constructed tires. They are also called conventional, x-ply, or cross-ply tires. Some motorcycle and trailer tires still use this internal construction.
Some run-flat tires are identified with an F followed by the type of internal construction.
E: WHEEL DIAMETER This two-digit number specifies wheel diameter in inches. It’s the distance between the two bead seat areas (where a tire gets tightly sealed onto the wheel).
F: LOAD INDEX The two-digit or three-digit number that follows the gap specifies tire load index. The load index symbol indicates how much weight a tire can support, based on the following standard chart. In our example, the load index is 89, which indicates the tire has a load capacity of 1,279 pounds, when inflated to the tire’s maximum air pressure rating.
G: SPEED RATING The last letter is the tire speed rating. This indicates the top speed it’s safe to travel at for a sustained amount of time. A tire with a higher speed rating can handle heat better and provide more control at faster speeds. The maximum operating speed of a vehicle is no more than the lowest speed rating of all tires mounted on the vehicle. (Of course, you should always abide by speed limits for safer driving.) Speed rating is usually, but not always, a single letter (see the chart).
Below you will find several charts that will help you understand tire sizing numbers, including a load index chart and speed rating chart.
A tire size calculator is a quick way to see whether the tire size you’re considering will likely fit your car, SUV, sports car, light truck or crossover.
But remember that is only an estimate. It’s important to stay within the sizing tolerances of your vehicle.
Tires that are the wrong size could cause some pull in the steering wheel, rub against the suspension or body of your vehicle, reduce clearance on hills, or result in a stiffer or noisier ride.
If you’re considering mounting a different tire size on your vehicle, check with a tire expert. Find out whether the tires and wheels you have your eye on are the right fit for your vehicle’s suspension, gearing, and bodywork. And ask how any differences in revolutions per mile, tire speed, load index, and speed rating will affect your ride quality and vehicle performance.
See how new tires and rims will look on your car or truck using our Virtual Wheels simulator, available at any Les Schwab.
Find Your Store
Tires
What would you say if you had to describe your tires in a few words? You might say something like, “They’re black, grooved, rubbery, and round.
” While you’re certainly right, you’re missing some key information—and it’s printed right on the tire! Find out what your tire numbers mean so you can make the best, most informed decisions about your tire and car care.
For the purpose of this piece, let’s pretend we’re looking at a tire with 215/65 R15 printed on its sidewall. What do the numbers on this tire mean?
“215” in this sequence refers to the tire’s width in millimeters. In other words, this tire is 215 millimeters wide, from sidewall to sidewall.
“65” in the sequence is the aspect ratio of the tire. The aspect ratio is a percentage, and it tells you the ratio of the tire’s height to its width. In this example, the aspect ratio number “65” means that the tire’s height is 65 percent of its width.
The “R” in this sequence refers to the construction of this tire.
Specifically, the “R” means that the layers run radially across the tire. The majority of tires on the road today are radial tires, in which the internal layers are perpendicular to the axis of rotation (and the direction of travel).
The other letter you might see here is a “D,” which denotes a tire that has a diagonal or bias ply construction. These tires have plies that are laid out in a diagonal, or crosshatch, pattern.
The very last number in the sequence, “15,” is the diameter of the tire. This is an important number—this is the number you’ll refer to when you need to know your tire size! The “15” indicates that this particular tire would fit a rim with a 15-inch diameter.
Now that you know how to read numbers on tires, you'll be able to describe your tires with much more knowledge and accuracy than, “black, grooved, rubbery, and round.” Check out our latest tire deals and head to your nearest Firestone Complete Auto Care to chat it up with people who speak tire, too! Our technicians are here for everything you need, from tire repair to tread depth checks.
Schedule
Tires
Tread wear, your tires exposure to the elements, and tire age may all be contributing factors to your needing new tires. Read on to learn how to tell.
Read More
Tires
Firestone tires create a whole new driving experience. Learn about the technology of our tires that improves driving on straightaways and handling ability.
Read More
Tires
Tires are an investment & you want them to last. Here are some tire care tips to help you get the most out of your tires & info on our free inspection
Read More
LOAD 3 MORE
SHOWING 6 OF 12
Tires
Wondering when to replace tires? You don't need any fancy tools.
Learn how to check tire tread depth with the tire penny test, with help from the pros at Firestone Complete Auto Care. It's quick, easy, and one of the best ways to ensure your safety on the road.
Read More
Tires
Wondering how to choose tires? Let us simplify the process into a handful of easy-to-follow steps, from Firestone Complete Auto Care.
Read More
Tires
Do you need to switch all of your tires to winter tires, or will two do just fine? Get the answer, from the tire pros at Firestone Complete Auto Care!
Read More
Do you want to choose a tire for your car, but do not understand tire markings well? It's not a problem! In this section, we will help you figure out what tire parameters are, what they mean, and which tire is right for your car.
195/65 R15 91 TXL
195 is the tire width in mm.
65 - Proportionality, i.e. profile height to width ratio. In our case, it is equal to 65%. Simply put, with the same width, the larger this indicator, the higher the tire will be and vice versa. Usually this value is simply called “profile”.
Since the tire profile is a relative value, it is important to take into account when choosing rubber that if you want to put tires with a size of 205/65 R15 instead of the size 195/65 R15, then not only the width of the tire will increase, but also the height! Which in most cases is unacceptable! (except when both of these sizes are indicated in the car's operating book). You can calculate the exact data on changing the outer dimensions of the wheel in a special tire calculator.
If this ratio is not specified (for example, 185/R14C), then it is equal to 80-82% and the tire is called full profile.
Reinforced tires with this marking are usually used on minibuses and light trucks, where a large maximum wheel load is very important.
R - means a tire with a radial cord (in fact, almost all tires are made this way now).
Many mistakenly believe that R- means the radius of the tire, but this is precisely the radial design of the tire. There is also a diagonal design (indicated by the letter D), but recently it has practically not been produced, since its performance is noticeably worse.
15 - wheel (rim) diameter in inches. (It is the diameter, not the radius! This is also a common mistake). This is the “landing” diameter of the tire on the disk, i.e. is the inside size of the tire or the outside of the rim.
91 - load index. This is the level of maximum permissible load on one wheel. For passenger cars, it is usually done with a margin and is not a decisive factor when choosing tires (in our case, IN - 91 - 670 kg.
). For minibuses and small trucks, this parameter is very important and must be observed.
T - tire speed index. The larger it is, the faster you can ride on this tire (in our case, IS - H - up to 210 km / h). Speaking about the tire speed index, I would like to note that with this parameter, the tire manufacturer guarantees the normal operation of the rubber when the car is constantly moving at the specified speed for several hours.
There are two different markings for American tires. The first one is very similar to the European one, only the letters “P” (Passanger - for a passenger car) or “LT” (Light Truck - light truck) are placed before the size. For example: P 195/60 R 14 or LT 235/75 R15. And another tire marking, which is fundamentally different from the European one.
Example: 31x10.
5 R15 (corresponding to European size 265/75 R15)
31 is the outside diameter of the tire in inches.
10.5 is tire width in inches.
R - a tire with a radial design (older tire models were with a diagonal design).
15 is the inner diameter of the tire in inches.
Generally speaking, except for inches that are unusual for us, the American tire marking is logical and more understandable, unlike the European one, where the height of the tire profile is not constant and depends on the width of the tire. And here everything is simple with decoding: the first digit of the standard size is the outer diameter, the second is the width, the third is the inner diameter.
XL or Extra Load is a reinforced tire, the load index of which is 3 units higher than that of conventional tires of the same size.
In other words, if a given tire has a load index of 91 marked XL or Extra Load, then this means that with this index, the tire is able to withstand a maximum load of 670 kg instead of 615 kg (see the table of tire load indices).
M+S or M&S tire marking (Mud + Snow) - mud plus snow and means that the tires are all-season or winter. Many summer tires for SUVs are labeled M&S. However, these tires must not be used in winter, as winter tires have a completely different rubber compound and tread pattern, and the M&S badge indicates good flotation performance.
All Season or AS all season tires. Aw (Any Weather) - Any weather.
Pictogram * (snowflake) — rubber is designed for use in harsh winter conditions. If this marking is not on the sidewall of the tire, then this tire is intended for use only in summer conditions.
Aquatred, Aquacontact, Rain, Water, Aqua or pictogram (umbrella) - special rain tires.
Outside and Inside ; asymmetric tires, i.e. It is important not to confuse which side is the outside and which is the inside. When installing, the Outside inscription must be on the outside of the car, and Inside on the inside.
RSC (RunFlat System Component) - RunFlat tires are tires on which you can continue to drive a car at a speed of no more than 80 km / h with a FULL drop in pressure in the tire (due to a puncture or cut). On these tires, depending on the manufacturer's recommendations, you can drive from 50 to 150 km. Different tire manufacturers use different designations for RSC technology. For example: Bridgestone RFT, Continental SSR, Goodyear RunOnFlat, Nokian Run Flat, Michelin ZP etc.
Rotation or arrow This marking on the tire sidewall indicates a directional tire. When installing the tire, you must strictly observe the direction of rotation of the wheel, indicated by the arrow.
Tubeless - tubeless tire. In the absence of this inscription, the tire can only be used with a camera. Tube Type - indicates that this tire must be used only with a tube.
Max Pressure ; maximum allowable tire pressure. Max Load - the maximum allowable load on each wheel of the car, in kg.
Reinforced or the letters RF in the size (for example 195/70 R15RF) means that this is a reinforced tire (6 layers). The letter C at the end of the size (for example 195/70 R15C) indicates a truck tire (8 layers).
Radial this marking on the rubber in the standard size means that this is a radial construction tire. Steel means that there is a metal cord in the tire structure.
Letter E (in a circle) - the tire meets the European requirements of ECE (Economic Commission for Europe). DOT (Department of Transportation - US Department of Transportation) is an American quality standard.
Temperature A, B, or C Temperature resistance of the tire at high speeds on the test bench (A is best).
Traction A, B, or C Tire wet braking capability.
Treadwear ; relative expected mileage compared to a specific US standard test.
TWI (Tread Wear Indiration) - tire tread wear indicators. The marking on the TWI wheel can also be with an arrow. Pointers are located evenly in eight or six places around the entire circumference of the tire and show the minimum allowable tread depth. The wear indicator is made in the form of a protrusion with a height of 1.6 mm (the minimum tread value for light vehicles) and is located in the tread recess (usually in the drainage grooves).
DOT - Manufacturer's coded address, tire size code, certificate, issue date (week/year).
Find tires / tire catalog A lot depends on the right choice of shoes for a car. When deciding to buy a kit, you can be guided by various comparative tests.
However, it is worth remembering that their characteristics must correspond to the operating conditions. In this case, the information indicated in the marking on the sidewall of the tire will help. Such inscriptions on the tire indicate the size of the product and its technological characteristics. Below we will decipher the symbols and try to figure out what the numbers and letters in the rubber marking mean.
We have a wheel with parameters such as 195 60 R16. This means that we have rubber in front of us, with a tread width of 195 mm.
The second number is the ratio of the picture's height to width. The larger this parameter, the more “hooky” the rubber will be. This value is usually referred to as the profile index.
The third number is the inner diameter of the tire in inches. In general, a common mistake is that motorists purchase wheels without paying attention to some data on changes in external parameters. For example, size 185 65 r15 will differ in height from 210 65 r15 with the same bore diameter. The ratio of the profile to the width in our case can interfere with the installation of tires on the car. This factor should be understood and taken into account. And a special calculator will help you correctly calculate the size of the tires.
Tire manufacturers also supply all tires with a speed index without fail. This sign can be found immediately after the wheel size indicator. It tells you how fast you can travel on the roads. A table that deciphers the speed index of passenger car tires will help to read this sign correctly.
| Tire speed classification | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Designation | N | P | Q | R | 9 | S | T | 9 | U | 902U 9022 H | 9 |
| Speed | 140 | 150 | 160 | 170 | 180 | 190 | 200229 | 210 9022E29 9028 240 240 |
Immediately after the speed index on the tires of the car there is an index of the permissible load on each wheel. For example, tire marking contains an indicator of 88t. This indicates that the machine can travel at a maximum speed of 190 km / h, and the maximum allowable load on each wheel is 560 kg.
Certain tires may be marked with the letters XL or the words Reinforced. This marking is usually awarded to tires, the load index of which is higher than standard values.
If the number 88 is written on the sidewall of an xl or extra load tire, then 3 should be added to the value. decipher this indicator as 91 or 615 kg per wheel.
| Number | load in kg one wheel for cars |
|---|---|
| 60-70 | 250-335 |
| 71-80 | 345-450 |
| 81-90 | 462-600 |
| 91-100 | 615-800 |
| 101-110 | 825-1060 |
| 111-120 | 1090-1400 |
| 121-129 | 1450-1850 |
American tire manufacturers resort to a different tire marking. The first one is very similar to the European one, only before the dimension there are additional letters P - passenger, LT - light truck or T - truck.
For example, 185 r14c P means that this is a wheel with a tread width of 185 mm, a diameter of 14 inches and designed for passenger cars.
The second classification system for its products is quite different. If the European system measures the dimensions of car tires in millimeters, then the American system measures in inches. However, it is quite easy to understand. For example, there are numbers on tires 27*11*r15. The first number is the outside diameter of the tire, the second number is the tread width, and the last number is the inside diameter.
To facilitate the mounting of wheels on rims, manufacturers sometimes equip additional color marks that carry their own information. How to decipher such icons - below.
Occasionally, a yellow dot or triangle can be seen on tires, which indicates the lightest spot on the tyre. When mounting, it is necessary to align the mark with the heaviest part of the disc to facilitate balancing.
Additional tire parameters include red circle or triangle symbols that can be found on the sidewall of the rubber. This is the designation of the most rigid place of the tire wall. It must be aligned with the “L” mark on the disk.
A white stamp with a number located on the outer sidewall bears information about the inspector who carried out the final "acceptance" of the goods.
Some tires have radial colored stripes. They help to identify tires of certain brands in the store, quickly look for them in the warehouse. Sometimes the color of the strip indicates the date of issue or the country of manufacture, and also indicates the passage of a run-in.
Many passenger tires have additional markings in addition to the model and tread type designation:
Differs from the inner sides with an asymmetric tread. It will help you figure out which side should be outside when installing a set of rubber on a car;
It is also worth understanding what the seasonal badges on the wheels mean.
