Your Tire Pressure Monitoring System is a valuable tool, but only if you pay attention when the Honda TPMS Warning Light comes on. When the tire light alerts you to low tire pressure – you will need to address the problem and reset the light.
Please remember that the tire pressure sensors are not a substitute for checking your tire pressure regularly. It won’t light up unless the problem is becoming serious. Underinflated tires can be a safety hazard.
Honda Tire Pressure Monitoring Systems vary, depending on the model type and model year. Furthermore, TPMS systems are not uniform across the spectrum of car brands.
In addition, the technology changes from time to time, meaning that older models may not have the same capability found on new ones. Here’s some good information that may answer some of your questions about TPMS and your tire warning light.
The tire pressure light isn’t required to come on until the tire is 25 percent below recommendations. Therefore, you should never ignore it. The manufacturer’s recommended air pressure is in your owner s manual.
The most likely trigger is cold. Tire pressure drops about 1 psi with every ten degree drop in cold weather. As your tires heat up, the pressure stabilizes. That’s why there are winter and summer standards for properly inflated tires.
Try driving the vehicle at over 28 miles per hour for a few minutes. At that speed, the TPMS will get little or less interference from other sensors and radio frequencies. This allows it to update through the serial data bus, sending the proper tire information to the TPMS sensor.
According to the National Highway Traffic Safety Administration, systems may flash or stay on longer to indicate a problem with the TPMS system rather than the tire.
After checking that your tires have the proper pressure, you may need a mechanic to read the code and tell you what’s happening.
The spare tire does not have a sensor for the TPMS system to read. The system may register nothing where the tire should be. As long as you are confident that the spare has the correct tire pressure, it should not represent a problem.
Unfortunately, human eyesight cannot detect that a tire is low until the problem is really severe. . Your manufacturer’s recommended pressure is in your owner s manual.
Some people try to clear codes by disconnecting the battery. Generally the system saves all codes and doesn’t reset them just because the battery is removed. This is actually a fail-safe feature because mechanics need those codes to determine what is wrong with a vehicle.
If you are able to clear the TPMS code, you will be overwriting it with a new code.
Unless the system triggers the sensor again, your mechanic will not find the important code.
According to the automotive journalists at Edmunds, a mere 5 PSI can cause a tire to fail. An underinflated tire generates heat as it struggles to keep up with the job it has to do. This causes faster degeneration.
Furthermore, an underinflated tire affects the accuracy of steering and handling. Thus, the vehicle declines in performance and fuel economy.
Direct TPM sensors are attached to the valve for the most accurate reading. With indirect TPMS, the anti-lock brake system assists in determining approximate pressure. Although a good system, it is not as fast as a direct system.
Starting with the 2008 model year, every Honda has TPMS. All cars made before the 2018 probably don’t have this feature.
If you don’t have a light to turn on and warning you, it’s all the more important to carry a gauge to check and add air as needed.
Explore the Earnhardt Honda inventory today to find a Honda car, truck or crossover with TPMS!
Learn how to reset the tire warning light with this step-by-step guide and get back to normal. Instructions To Reset the Honda TPMS Warning Light
Posted in Features, Model Information, Service, Tips and Tricks | No Comments »
Is there an easy way to reset the tire pressure light on a Honda Accord from 2016? I filled up the tires last week and my mechanic told me the tires are fine.
I have a touchscreen if that makes a difference.
Liz Jenson · Answered on Oct 28, 2021
Reviewed by Shannon Martin, Licensed Insurance Agent.
Since you’ve already had your tires refilled and checked by a mechanic, you probably just have a faulty tire pressure light. Follow these steps to reset the tire pressure light in your 2016 Honda Accord:
Remember, your tire pressure light usually indicates low pressure in one or more tire/s. Driving with a deflated tire could put you at a higher risk of flat tires or uneven tire wear.
In a worst-case scenario, your tire could pop—leaving you stranded on the side of the road.
To protect yourself in the case of a mechanical breakdown, get roadside assistance with Jerry. Jerry’s leading roadside assistance gives you access to their network of over 55,000 service providers. That way, you’re covered with towing, key replacements, jump starts, and more—no matter where you are!
MORE: Low tire pressure in cold weather, and how to fix it
HondaCar MaintenanceCar Repair
View full answer
WHY YOU CAN TRUST JERRY
Jerry partners with more than 50 insurance companies, but our content is independently researched, written, and fact-checked by our team of editors and agents. We aren’t paid for reviews or other content.
Browse More Content
Car Heater Hose Replacement
Car Air Pump Replacement
What To Do If Your Engine Hesitates During Acceleration
Fuel Pressure Sensor Replacement Cost Estimate
Noise From Engine or Exhaust Inspection Cost Estimate
Oldsmobile Cutlass Ciera Sl Insurance Cost
Jeep Cherokee Limited Insurance Cost
Infiniti Fx37 Insurance Cost
Ford Crown Victoria Police Interceptor Insurance Cost
Saturn Sky Redline Insurance Cost
Swansea Car Insurance
Crossett Car Insurance
Minonk Car Insurance
Tulalip Car Insurance
Park Hill Car Insurance
I want to buy a car with a rebuilt title, but no lender will approve me for a loan.
Can I take out a signature loan to buy the car?
Eric Schad
Oct 29, 2021
I want to buy a new car, but the lender will only approve me for a partial amount. Can I take out a second loan to get the rest of the money?
Eric Schad
Oct 29, 2021
My bank has a great rate (about 2%) on home equity loans right now. I also need a new car. Can I use the home equity loan to purchase a car—is this a good idea?
Eric Schad
Oct 29, 2021
Browse All Questions
Keep an eye out for Japanese grass, Callery pears, and privets on your Missouri property. They’re some of the state's most invasive plant species.
Patrick Price
Oct 11, 2022
Unlock your Honda steering wheel by firmly pulling it to one side while turning the key in the ignition.
Follow along for all the details.
Patrick Price
Oct 04, 2022
Demand for electric cars is higher than ever, but automakers are struggling to keep pace with consumer interest.
Patrick Price
Oct 03, 2022
Texting and Driving
Uninsured Motorist Protection
Car Repairs
Car Registration Renewal
Allstate
Car Reviews
Chevrolet
Road Safety
New York
Personal Injury Protection (PIP)
21st Century
Drunk Driving
Commercial Trucks
Bundling
Car Insurance Discounts
Cheap Auto Insurance
Drivers with Disabilities
Direct Auto Insurance
Velox Insurance
Massachusetts
Florida
Distracted Driving
Auto and Home Insurance
No long forms
No spam or unwanted phone calls
Quotes from top insurance companies
Find insurance savings — it's 100% free
Toyota
Hyundai
Mercedes-Benz
Subaru
Chevrolet
Mitsubishi
You are the proud owner of a recent car, the benefits of tactile gadgets, the integrated technologies should bring you a significant usability of your Honda Accord, however, it says that the technology is talking about electronic, and as we all unfortunately know , in some cases problems that need to be fixed.
Today we will focus on the tire pressure sensor and specifically on the tire pressure sensor. nine0003 how to reset the tire pressure sensor on a Honda Accord so that this indicator never appears on the dashboard again. In order to achieve this, we will divide our article into two parts: first we will focus on the classic situation where the tire pressure indicator light occurs and the subsequent process, and then on the circumstance that the tire pressure indicator remains on even if the tires are inflated. So how to reset this tire sensor on honda accord.
First, we will focus on the classic way to reset a tire sensor on a Honda Accord, which if it lights up, here are the basic tricks: tire pressure indicators on your Honda Accord, get out of the way immediately if you are driving on the highway, keep a firm grip on the steering wheel just in case.
Now that you have tried the normal process of removing the tire pressure sensor on the Honda Accord, and this didn't work, we'll move on to the second alternative, which is to have the tires on my Honda Accord well inflated and I still want that light to go out. This almost certainly means you have Faulty tire pressure sensor.
For this important reset the value on the dashboard of your car. However, be careful not to do this while driving as pressure fluctuations will interfere with your sensors. In most cases, you need to go through the car configurations, then you should find an option for inflation detection or "deflation detection". While on this tab, you must hold down the Select or Reset button, depending on the year of your Honda Accord, until a message appears from the car console confirming that the reset is being taken into account (usually takes a few seconds). You can now turn off the ignition and restart your Honda Accord to see if the tire pressure light has gone out. nine0005
However, this procedure is not recommended as it may result in improper handling and malfunction of your Honda Accord. Now you have all the keys in your hands to know how to reset the tire pressure sensor on your Honda Accord. nine0005 If you have any further questions about the Honda Accord, do not hesitate to contact us. Honda Accord category.
Save article:
The article says:
When the tires are optimally inflated, the low tire pressure indicator (TPMS) does not light up on the vehicle's dashboard. However, in some cases, it lights up even if the pressure is normal. This can't help but be annoying, especially when the tires are inflated normally.
In our article today, we will figure out how to reset a tire pressure error.
American and European scientists conducted a study, during which it was found that most drivers do not check whether the wheels are properly inflated before getting behind the wheel of a car. Only 40% of car owners perform such a check - and even then only once every 12 months. This is the reason for a large number of accidents. nine0005
The TPMS (Tyre pressure monitoring system) system is designed to monitor tire pressure, as well as warn of a malfunction. If the tires are under-inflated or over-inflated, an error will be displayed on the remote control or an audible signal will appear.
What is dangerous too high or, conversely, low pressure? The risk of an accident increases, the car begins to consume more fuel, in addition, the rubber wears out faster.
Photo: Shutterstock nine0005
The above devices operate on the same principle.
Let's figure out how information about what tire pressure gets to the control panel.
Consider how pressure is calculated by measuring instruments.
Typically, the sensor performs a comparison of the angular rotation of the wheel. Knowing the value of this parameter, you can calculate the distance that the wheel will travel in one rotation.
Obviously, if the tires are under-inflated or over-inflated, then the outer diameter of the wheel will be different. Visually, a person cannot determine this change. But the sensor notices even such changes. The system fixes non-compliance with the required parameters. nine0005
The sensor will still respond, despite the fact that the wheel circumference has changed quite a bit. In this situation, it is necessary to find out what mechanical reason led to this. Only in this way can you eliminate the misinterpretation of the signals transmitted by the system. This can happen because:
Also, the TPMS system gives an error when you install new wheels or rearrange them.
When, after these steps, a tire pressure error appeared, indicating unbalance, you should reset the settings, and then set the basic parameters. In this case, the control signal may remain even if the basic settings have been selected.
Why such problems may occur:
At the same time, as soon as you drive out onto an asphalt surface or start driving calmly, the error disappears. nine0002 See also
"Velcro or spikes: which rubber is better for the Russian winter"
Read more
How to reset tire pressure error? To begin with, imagine that the TPMS system is working properly and the blinking light indicates a problem with the undercarriage of the machine. The first thing you should do is slowly release the gas. You can not brake sharply, turn the steering wheel. After the car has stopped, inspect the tires to make sure the rubber is not punctured or broken. Then you can check if the tire pressure is normal. nine0005
Pay attention! The TPMS will not always show a tire pressure error. For example, if the tires are slowly deflating, the system will not inform you about the problem.
In the same way, she will not notice the error if the tire pressure starts to drop rapidly. This usually happens when a tire ruptures. This feature of the TPMS system is explained by the specifics of identifying and counting nonconformities.
However, in some cases, it happens that the TPMS system indicator is on, but the tires are in perfect condition. How to reset tire pressure error? We understand. nine0005
The complex TPMS system in some cases starts to work incorrectly. Usually, car owners observe the following picture: a tire pressure error is displayed on the display (the tire is underinflated), but in reality everything is fine with the wheel. You have to reset the tire pressure error. Otherwise, the TPMS system starts to work incorrectly.
Photo: Shutterstock nine0005
You also have to reset the tire pressure error when there is radio interference from high voltage power lines.
Or when sources of radio signals are located in the immediate vicinity. But as soon as you move away from them, the pressure error disappears and the system begins to function properly.
The reason for the malfunction may lie in the sensor, which is "failed". This damage cannot be easily repaired. How to reset a tire pressure error if the sensor flashes, while you hear a beep, lose your vigilance and find it difficult to drive a car? There are 4 ways to fix this problem. nine0005
To reset the error, pick up a speed of 80 km / h and continue driving for another 15 kilometers.
This method is the easiest to implement. If your car has this feature, then turn on the cruise control so that the speed does not change. Depending on the model of your car, you will be able to reset the tire pressure error at a speed that exceeds the specified one. After you cover a distance of 15-20 kilometers, maintaining the same speed of 80 km / h, make a stop.
Turn off the motor. When you start it again, the tire pressure error will disappear. nine0005
Popular articles
How to choose a subwoofer for your car
19.12.2022
231
From top to bottom, obliquely: how to degrease a car body before painting
12/15/2022
168 nine0005
Chic, shine, beauty: how to remove scratches on a car with your own hands
9.12.2022
232
Without damage: how to reduce the fuel consumption of your car
11/29/2022
244
nine0054 How much do they pay for advertising on a car11/25/2022
663
Press the tire pressure monitoring system (TPMS) reset button on your car and you will be able to reset the error.
It does not matter what type of low pressure warning system is used. In any case, there will be a sensor on each wheel of your car. Sometimes it may be necessary to reboot the touch system of the car. Read the owner's manual for the vehicle. It contains information on how to reset a tire pressure error. Most often, the instructions indicate which button to press to reset. nine0005
The ignition key must be in the lock. No need to start the car, just turn it to the “on” (“ON”) position. Then press and hold the reset button, which may be under the steering wheel. We are waiting for the low pressure indicator to blink 3 times. After that, you can release the button. We start the car, it should work for 20 minutes. After this time, the computer will calibrate the sensors on the wheels. Now you can turn off the car.
nine0002 See also
""
Read more
Lower and then re-inflate the wheels.
Failed to reset tire pressure error using the previous method? Then we inflate all tires to 0.2 bar, this is the pressure that should be according to the recommendations of car manufacturers. Did the error go away? Then we lower the pressure in the tires completely.
Now we pump up the wheels again. The pressure in them should be the same as indicated on the driver's door pillar or in the car's operating instructions. When there are sensors on the wheels, you need to remember about the spare tire. Now you need to drive about 3-5 kilometers, adhering to a speed of 25 km per hour. So you can reset the tire pressure error. nine0005
Remove the battery terminals and then connect it to reset the error.
Each car has a computer that receives data from all kinds of vehicle sensors, including TPMS system sensors. However, any electronics can fail. To reset the error, you will have to reboot the system, for which you need to turn off the power.
Photo: Shutterstock
To do this, open the hood. The battery is located under the hood. Disconnect the negative terminal from it. To perform this operation, use a wrench. Then sit in the driver's seat, turn the key to the "ON" position, but do not start the car. Now you need to press the signal for 3 seconds. This will use up the energy that remains in the electrical system of the machine. Then reconnect the battery. This way you can reset the error. nine0005
Sensors keep track of tire pressure. However, you need to be sure that they function properly. Of course, you do not need to constantly walk around with a special measuring device and find out the status of the sensors. It just needs to be calibrated from time to time.
It is performed quite simply. The most important thing to remember is that, depending on the make and model of your car, for each wheel there are pressure parameters strictly defined by the manufacturer for winter and summer.
These values should be given to the sensors. How the installation and configuration will be performed depends on the controller used. nine0005
Experts do not recommend using the internal controller yourself. However, additional settings are not required if the data is read using the screen that is directly on the control system. For current promotions on the Halva card, which will help you profitably purchase household appliances, you can follow here. nine0005
To prevent a tire pressure error from appearing, it is important to calibrate (adjust the TPMS system) every time a change is made. For example, when you installed a new set of wheels, repaired tires, did balancing, and the like. Using TPMS controllers is quite simple. The main thing is to read the instructions for use of the device. And make sure that the tire pressure is the one recommended by the car manufacturer.
nine0002 See also
"What tires can be put on rims 14, 15 and 16: advice from professionals"
Read more
Every car owner gets annoyed if the tire pressure error icon lights up on the dashboard.
