by Nicula Rose
Many parents do not take care of the stroller wheel whether it is fully air or not. The stroller can not be operated properly without full air filling in the wheel inner tube.
If you want to get the highest performance of a stroller then you must have to keep an eye on the wheels. Especially Before going out with a baby stroller, make sure that the air is full in the stroller wheel.
Today we will discuss in detail how to inflate bob stroller tires to get the optimum performance and some more discussion about the best pump and best tire in the market.
Page Contents
Don’t forget to bring some tools that will make your pumping experience awesome.
If you own a Bob stroller, chances are you will eventually need to inflate the tires. While this may seem like a daunting task, it is actually quite easy to do. With a few simple tools and a little bit of know-how, you can have your stroller’s tires inflated in no time.
The first thing you will need is an air compressor. You can find these at most hardware stores or online. Once you have your air compressor, attach the hose to the tire valve. Then, open the valve and start pumping air into the tire.
It is important to check the pressure frequently while inflating the tire. You can use a pressure gauge to do this. Once the tire is inflated to the desired pressure, close the valve and remove the hose.
That’s all there is to it! Inflating your Bob stroller’s tires is a quick and easy process that anyone can do.
The method of pumping is different due to different models of wheels. Below I will describe how to inflate the most popular tires in the present market.
First of all, remove the wheel from the stroller and open the valve stem cap from the valve stem tire. Follow the instruction (PSI limit) written on the wheel. Some tire PSI capacity is 235- 250 and some wheel capacity is more or less. It depends on the brand and model.
Now you can start pumping and check if is it okay or not. Never try to pump with a gas pump.
How to pump a bumbleride stroller wheelSome parents face trouble pumping up the stroller bumbleride wheel. Here is a solution for you. Check and make sure that the tire is properly seated with the rim, If not, adjust and re-align.
Now open the valve stem cap and pump till inflate up to 30 PSI. Standard PSI is 35 but we recommend 25. Be careful about overfilling.
Note: The best way to pump is foot and hand pump to 25-30 PSI.
How to pump up a bugaboo pram tireIt’s important to know the process of inflating a tube before the pump.
At first, unscrew the valve cap. Carefully attach or screw the pumper wheel valve and fill the air as required. If you inflate manually, follow the PSI up to 25-35. But the standard PSI is 30. After filling the air don’t forget to screw the valve cap.
Note: Please don’t use a gas pump to inflate the tube.
Final thoughtFinally, I am at the end of the detail explaining how to pump the bob stroller tire. Whether you try to inflate air in your stroller wheel, follow the process for better performance.
In case you don’t have a pump yet or are looking for an excellent quality pump then go through the Incredibly Useful Best Bob Stroller Inner Tube to pick the suitable one for you!
You are here: Home / Stroller Accessories / Learn how to inflate (fill air in) tire of a baby stroller correctly
by strollerboards Leave a Comment
StrollerBoards.
com is reader supported. When you buy through links on our site,
we may earn an affiliate commission. Learn more.
Learn how to inflate (fill air in) tire of a baby stroller correctly.
Lot of parents/caretakers don’t check whether there is sufficient air in the baby stroller tires.
A well filled stroller tire will offer your baby a smoother ride and allow the stroller to perform at its optimum point.
What we have observed is that most parents don’t clearly understand how to properly inflate a strollers’ tire.
Here’s more on how to do that correctly.
Here’s what you need to inflate the stroller tires.
You will need an air pump, gloves, inflator. You will need the right stroller air pump; in most cases, bike pumps will fit in stroller valves too.
There are different types of pumps, inflators, tubes, tires, and valves. Keep that in mind before starting.
Depending on what type of valve the stroller tire has, you may require a specific pump head for its inflation.
There are two basic types of valve head you can use – Schrader-pump-head or the Presta valve tube.
There are lot of air pumps that have a dual pump head attachment, or if you’re sure which valve your stroller tire uses, you may get the appropriate pump for your stroller (Schrader or Presta).
There are times when the stroller tires will have less air in them, and they will need to be inflated in order to have a smoother ride. However, pumping air in the stroller tire may not be as simple as you think
There are many who pump air into the tire with their pump, but the tires just won’t inflate. That is because on most strollers, you need to press a locking lever in order to allow the air to pass into the tyre.
Most stroller tires have a lever next to the hole (valve) from where the air comes in and goes out. Once you attach the pump to the air valve on the tire, you need to lift the lever. Doing this allows the air to flow through into the tire.
Once you’re finished pumping air, and the tires are inflated, you need to lower the lever back to its original position, and remove the pump.
Here are a few videos that show how to inflate (fill air in) tires of various strollers.
strollerboards
StrollerBoards is a family managed website with me (Ben) and my wife doing most of the work. We are proud parents of two wonderful kids and love reviewing baby travel gear. We have a firm but friendly “democratic parenting” style and offer several practical solutions backed by extensive research.
Our own experience with raising two children prompted us to share our knowledge. Read more.
Filed Under: Stroller Accessories
report this adThe design of the devices is simple, but there are several types of pumps that differ in functionality, weight and appearance.
Electric pumps can only be operated when connected to the mains. Some models are battery operated. The advantage of such products is the minimum participation in the process of human work. In addition, the pumping itself takes place in a matter of seconds.
Leg Structures are easy to use as they only use one leg. They do not need electricity, and thanks to the simplicity of the products, even children can use them. With the help of a foot device, you can pump up not only the wheels of the stroller, but also the pool or mattress.
Water filter pumps are indispensable for inflating frame or inflatable pools. This type of product is not suitable for restoring pressure in the wheels of baby carriages. Therefore, when buying a pump, it is important to pay attention to its type and purpose.
A flat tire does not always mean that it is punctured.
Over time, even if the stroller is not used or the wheels are inflated irregularly, air comes out of the chamber (albeit slowly, but losses still occur).
Different wheels leak air at different speeds. Perhaps one wheel loosened faster than the others.
In this case, it is enough to pump it up and wait for a while. It takes 15-30 minutes to see that the air comes out very quickly and this indicates the presence of a puncture.
A punctured chamber must be sealed or replaced with a new one.
You can do it:
If you have the necessary tools and a pump; The technology for removing the tire from the rim and changing the tube is not much different between sidecars, bicycles and motorcycles. Therefore, strollers are easily accepted for repair in bike shops and tire services.
Under-inflated tires make driving difficult! Inflated tires make it difficult to ride and also increase the chance of a tire puncture.
It is necessary to inflate the wheels only with a hand pump, foot pumps are allowed, it is not recommended with compressors, if there is no way out, then carefully monitor the allowable pressure gauge readings!
Before inflating the wheels on the baby stroller, you should study the technical data sheet of the product. This document indicates the size of the tires and the allowable tire pressure. If this information is not in the technical passport or the document is lost, you can find the necessary information about the pressure indicators directly on the wheel tire. Very often, manufacturers place this information on the frame on stickers that indicate the permissible tire pressures.
The tire pressure is measured using a pressure gauge. If it is absent, it can also be detected manually by squeezing the spikes by pressing with a hand with little effort. Tire pressure for 8" to 14" tires will vary depending on where they are installed:
6 to 0.7 BAR; winter period - from 0.5 to 0.6 BAR; If the tire pressure is exceeded, the children's vehicle will move hard, which can lead to puncture, as well as spontaneous removal of the tire from the rim. Otherwise, with low tire pressure, the process of traffic will be difficult.
The process of inflating wheels is quite simple and does not require special technical knowledge, so you can do it yourself. The main requirement is the presence of a pump. Tires can be inflated without removing the wheel from the stroller:
Timely maintenance of children's vehicles will minimize the risk of making the necessary repairs at the wrong time. As for the chassis, you can also purchase special wheel covers for the baby stroller.
They will not affect the functioning of the transport itself in any way, but they will help keep the apartment clean (in the case of transport storage in the corridor or on the balcony), as well as in the car trunk (during transportation).
If you have experience in changing the bicycle tube and the necessary equipment, it will not be difficult to cope with the wheel from the stroller.
The following tools and equipment are required to change the inner tube yourself:
The sequence of actions would be:
So, alternately changing the blades, pull out one half of the tire. 
Pay attention to the rim. On the surface, where it comes into contact with the camera, there should be a protective tape called a “flipper”. This tape protects the camera from damage from the side of the rim. It may have burrs, scratches and joints. If there is no such tape, you need to wrap electrical tape on the rim or, in extreme cases, wide tape in several layers.
In this case no side vanes are required. To replace the camera you will need:
Both halves are attached to each other with 5 screws:
Insert the nipple into a special groove designed for it; Rims of this type are often rated at 1 bar. If you inflated more by mistake, then from excessive pressure the screws can be torn out of the plastic, the threads will break and the wheel will fall apart into two parts. If this happens, you need to pick up screws of a slightly larger size and length and screw them into the same holes. In plastic, they will roll a new thread and will firmly hold both halves together.
Inflation of wheels and replacement of the tube are not complicated procedures that require technical skills. Any man can quite master them. And this skill will come in handy later. After all, the child is growing. He will have a bicycle, which also needs technical care. You can contact any bicycle service, where those who wish will be happy to teach these simple operations.
Sources
[hide]
If a small child appears in the house, then purchasing a stroller becomes one of the most necessary purchases. It allows you to spend more time outside.
For a baby, this is a bed, a house, and a mode of transport. In it he sleeps, eats, walks, plays.
Like any piece of equipment, wheelchairs have various kinds of malfunctions that have to be fixed. Sometimes at the most inopportune moment, the question arises sharply - how to pump up the wheels on a baby stroller.
Contents
1 Method for replacing the tube if the stroller has plastic wheels consisting of two halves Over time, even if the stroller is not used or the wheels are inflated irregularly, air comes out of the chamber (albeit slowly, but losses still occur).
Different wheels leak air at different speeds. Perhaps one wheel loosened faster than the others.
In this case, it is enough to pump it up and wait for a while. It takes 15-30 minutes to see that the air comes out very quickly and this indicates the presence of a puncture.
A punctured chamber must be sealed or replaced with a new one.
You can do it:
The technology for removing the tire from the rim and changing the tube is not much different between sidecars, bicycles and motorcycles.
Therefore, strollers are easily accepted for repair in bike shops and tire services.
When a flat tire, it is urgent to fix this problem.
If this is not done in a timely manner, then the stroller:
Tire pressure must be monitored and inflated regularly.
Inflate with:
How to do this will be explained and shown when buying a pump in a bicycle shop. For pumping, you need to firmly insert the pump into the nipple and squeeze out the special fixing tab. If the pump has a pressure gauge, you should be guided by its indicators, in the absence of such, it is enough to press the tire with two fingers. If the tire is pressed through 2-3 mm under each finger, then the pressure is within normal limits. 
5 bar on the tire. If this is not noticed and pumped up to 2.5 bar, then the tire will withstand, but excess pressure can deform or break the plastic rim. Wheels should be inflated once every 3-4 weeks. If this is not done, then the stroller rides very hard and is poorly controlled.
Under-inflated tires wear out quickly, crack and need to be replaced prematurely.
Not all stroller wheels are easy to inflate.
Sometimes it happens that the nipple is placed between the spokes or rim elements.
Due to the small diameter of the rim, the nipple cannot be reached by the pump.
Conscientious manufacturers complete strollers with tubes, in which the nipple is not straight, but bent at an angle of 110 degrees and a little longer. When buying a replacement stroller or camera, you should pay attention to this. If the camera has a straight nipple, which is difficult to reach, then in bicycle shops you can buy a curved adapter for strollers and children's bicycles.
Once a month it is enough to make 10-20 strokes with a hand pump or 5-6 strokes with a floor pump, in each wheel.
When disassembling a tire, never use a screwdriver or other sharp metal objects. A screwdriver can severely damage the tube and leave burrs on the rim, which will subsequently lead to numerous punctures.
If you have experience in changing the bicycle tube and the necessary equipment, it will not be difficult to cope with the wheel from the stroller.
The following tools and equipment are required to change the inner tube yourself:
The sequence of actions would be:
You can press a screwdriver, a match or a pen on the spool of the nipple and wait until all the air has escaped. 
Pay attention to the rim. On the surface, where it comes into contact with the camera, there should be a protective tape called a “flipper”. This tape protects the camera from damage from the side of the rim. It may have burrs, scratches and joints. If there is no such tape, you need to wrap electrical tape on the rim or, in extreme cases, wide tape in several layers.
In this case no side vanes are required.
To replace the camera you will need:
Both halves are attached to each other with 5 screws:
These types of rims are often rated at 1 bar. If you inflated more by mistake, then from excessive pressure the screws can be torn out of the plastic, the threads will break and the wheel will fall apart into two parts.
