by Nicula Rose
Many parents do not take care of the stroller wheel whether it is fully air or not. The stroller can not be operated properly without full air filling in the wheel inner tube.
If you want to get the highest performance of a stroller then you must have to keep an eye on the wheels. Especially Before going out with a baby stroller, make sure that the air is full in the stroller wheel.
Today we will discuss in detail how to inflate bob stroller tires to get the optimum performance and some more discussion about the best pump and best tire in the market.
Page Contents
Don’t forget to bring some tools that will make your pumping experience awesome.
If you own a Bob stroller, chances are you will eventually need to inflate the tires. While this may seem like a daunting task, it is actually quite easy to do. With a few simple tools and a little bit of know-how, you can have your stroller’s tires inflated in no time.
The first thing you will need is an air compressor. You can find these at most hardware stores or online. Once you have your air compressor, attach the hose to the tire valve. Then, open the valve and start pumping air into the tire.
It is important to check the pressure frequently while inflating the tire. You can use a pressure gauge to do this. Once the tire is inflated to the desired pressure, close the valve and remove the hose.
That’s all there is to it! Inflating your Bob stroller’s tires is a quick and easy process that anyone can do.
The method of pumping is different due to different models of wheels. Below I will describe how to inflate the most popular tires in the present market.
First of all, remove the wheel from the stroller and open the valve stem cap from the valve stem tire. Follow the instruction (PSI limit) written on the wheel. Some tire PSI capacity is 235- 250 and some wheel capacity is more or less. It depends on the brand and model.
Now you can start pumping and check if is it okay or not. Never try to pump with a gas pump.
How to pump a bumbleride stroller wheelSome parents face trouble pumping up the stroller bumbleride wheel. Here is a solution for you. Check and make sure that the tire is properly seated with the rim, If not, adjust and re-align.
Now open the valve stem cap and pump till inflate up to 30 PSI. Standard PSI is 35 but we recommend 25. Be careful about overfilling.
Note: The best way to pump is foot and hand pump to 25-30 PSI.
How to pump up a bugaboo pram tireIt’s important to know the process of inflating a tube before the pump.
At first, unscrew the valve cap. Carefully attach or screw the pumper wheel valve and fill the air as required. If you inflate manually, follow the PSI up to 25-35. But the standard PSI is 30. After filling the air don’t forget to screw the valve cap.
Note: Please don’t use a gas pump to inflate the tube.
Final thoughtFinally, I am at the end of the detail explaining how to pump the bob stroller tire. Whether you try to inflate air in your stroller wheel, follow the process for better performance.
In case you don’t have a pump yet or are looking for an excellent quality pump then go through the Incredibly Useful Best Bob Stroller Inner Tube to pick the suitable one for you!
Home / Expert Tips / How to Pump Bob Stroller Tire | 6 Simple Steps
Expert Tips 2 Comments 796 Views
As an Amazon Associate I earn from qualifying purchases.
A stroller is beneficial in many ways. It lets you stay close to your baby while jogging, shopping, or a walk around. Babies also enjoy this awesome trip with you. A stroller simply fits into the family until it is safer for your baby. Maintain the stroller well to ensure its longevity. Since there are many components in the stroller, the tires are the most important ones. Tires help to ride the stroller and move forward.
If your stroller tires don’t have enough air, the stroller won’t move smoothly. It doesn’t properly operate without fully air-filled tires. Sometimes inflated tires may cause accidents. So whenever you are taking out your baby with a stroller, check the tires and make sure they are air-filled. Many parents don’t know how to pump Bob’s stroller tire. Here we will guide you on how to properly pump Bob’s stroller.
Contents
2 Step 2: Prepare the valveIn this guide, we try to give ample knowledge about pumping Bob tires. To pump your Bob stroller tires, you need to perform certain steps.
Step 1: Arrange the right toolsIf you own a stroller, you must have some basic tools like an air pump, inflator, gloves, etc. These tools are a must to pump the tires. However, you need to get the right pump that effectively works. Often, bike pumps are suitable to pump the stroller tires. But consider the tire type at first.
There are mostly two types of tire valves: Schrader or Presta. You can find two types of pumpers for these two different valve heads. However, some pumps have a dual pump attachment.
If you have a dual pump attachment, then inspect your stroller tire valve and get the right pump. Most Bob strollers have Schrader tire valves.
The valve is closed with a plastic cap. So first, you need to remove the cap to pump the tire. Suppose you lost the cap, no big deal if the tires have a Presta valve head. On the contrary, the Schrader valve is sealed with a tiny nut. In this case, you need to unscrew the valve. The nut won’t miss as it is screwed inside the valve head.
Step 3: Know tire pressureSince different stroller tire models have different tire pressure, you need to inspect the tire PSI range. Many stroller tires’ PSI range is 235-250; your one may have more or less. Check the sidewalls for knowing the PSI range as you don’t want to overfill the tire with air. Additionally, check any wear and tear in the tire. If the tire is worn out, you may need to replace it.
Step 4: Attach the pumpYou need an inflator to pump the stroller tires.
Attach the inflator at the end of the pressure pump. Once you attach the inflator, fit the pump in the tire valve head, and make sure it sits properly.
Some pumps have the threaded screw or flipping a switch to fit the pump head. It securely holds the pump head and doesn’t allow it to escape air. If there is no air leakage, you can effectively and quickly pump the baby stroller. Further, you can create a sealed system for effective pumping. However, while pumping always keep an eye on the gauge.
Step 5: Pump to the right levelEvery parent wants a bump-free ride for babies. So you need to pump the tubes to the optimal pressure. Many best pumps have gauges, so check on it and don’t be rough on the pump. Then counter check to see if the rest of the tires are filled with air at the right levels.
Step 6: Remove the pumpOnce the tire reaches the right pressure level, pop off the pump head or flip switch it. Unthread the pump head. Then re-attach the locking nut in the Schrader valve or close the valve cap.
If your stroller has a flat tire, then only pumping won’t solve the problem. There may have been damage to the inner tube. The inner tube is the significant part that holds the shape of the tire when pumped up. For flat tires, you want to replace the whole tire unit. But you don’t need to. Changing the inner tube may solve the problem.
Firstly, remove the tire and inner tube from the stroller to inspect them properly. Now, you need to check the tread if there is any large hole or rip on the inner tube. After checking visually, run your fingers gingerly inside of the tire for anything sticking out.
Then fix the punctured inner tube. You need to pump up the tube and submerge it in a large bowl filled with water. If bubbles originate from the tube, then understand there is a hole inside the tube. Mark the spot and patch it up.
Many BOB strollers have an aluminum wheel. If the rubber rim strip is missing and exposes the spoke nipples, then the inner tube may be defective.
The spoke nipples should be covered. In this case, the rubber rim strip works like a barrier between mental spoke nipples and the inner tube. If the rim strip is defective, replace it or use some duct or wheel tape. However, the rubber rim strip is specific for the Aluminum wheel, not for the polymer wheels.
Can you use a bike pump on Bob’s stroller?
You can use the bike pump on the Bob stroller but don’t be harsh to the tire. You need to gently pump the tires. It would be better if you check the gauge system while pumping for proper air filling.
What is the recommended air pressure for BOB stroller tires?
In most Bob plastic wheels, the inflation pressure is 30 pounds PSI. When inflation pressure is right on the wheel, it will run smoothly.
Do stroller tires have tubes?
Yes, stroller tires have inner tubes that hold the air and give the expected shape. If there is any leakage on the tube, the stroller tire will be flat and won’t run properly.
Final Words
Tires in the stroller are significant for an enjoyable ride for the baby. That’s why you should not neglect to maintain the tires. You need to pump it properly with the right tool. Also, make sure the inner tube of the tire is properly air-filled and doesn’t have any leakage. Don’t use sharp things like a screwdriver to bring out the inner tire. This article is a complete solution for you. Following the steps, you can properly pump the BOB stroller tire.
As an Amazon Associate I earn from qualifying purchases.
How To Fix a Bob Stroller Flat tire? 2022-04-02
Tags How To Fix a Bob Stroller Flat tire?
Previous How to Extend Stroller Handles | 4 Easy & Simple Steps
Next Are Stroller Bassinets Worth It | Should You Buy Or Skip It
As an Amazon Associate I earn from qualifying purchases.
When your baby does not want …
A bicycle pump is a must for every cyclist. It may be necessary to inflate the wheels more than once, especially on a long journey, so it becomes necessary to always have a pump with you.
This is how the tube is inflated with a compact bicycle pump.
There are many types of bicycle pumps. Starting from bulky and heavy floor pumps, which can be easily inflated in a matter of seconds, to compact and lightweight road pumps. We will consider several types of pumps so that you have some idea about them and can make a choice.
Sooner or later, every cyclist is faced with such a problem as a punctured tire. The replaced wheel needs to be pumped up. This is where you need a bike pump.
They make it quick and easy to inflate a wheel. But due to their considerable size, it is better to use such pumps at home or in the garage. Among the advantages, the following features can be distinguished:
| 1) Because the pump chamber is large, it pumps quickly. As disadvantages, significant weight and non-compact dimensions can be noted. This is what makes it difficult to take such pumps with you. |
This type of pump is easy to take with you. That is what they are designed for. For maximum convenience, buy a pump with a folding T-handle. It is best to choose a pump that is not the cheapest, since a compact bike pump is exposed to the environment (moisture, dust and dirt). And even better with an aluminum rather than a plastic case - it will last much longer. |
Due to its characteristics, this type of pump does not have the disadvantages of a floor pump, but many of the advantages of the second one have become its disadvantage.
Cons:
1) Slow pumping because of the small camera.
2) Most of the time there is no hose.
3) Not always a convenient pressure gauge, and even that is a rarity.
4) When inflating a wheel, such a pump is supported by weight.
5) As tire pressure increases, pumping becomes more difficult.
6) Reduced service life. The pump is exposed to rain and exposed to dirt and dust from the road.
Many modern pumps are equipped with a double pumping system, which will speed up the process by half. The most compact are telescopic pumps, but their design is too complex and therefore not very reliable and can quickly break down.
Even more compact pump design. They do not need to pump the wheel, they fill it with air due to replaceable gas cylinders in a matter of seconds. The main disadvantage of this type is the cost. Firstly, the pump itself is expensive, and secondly, frequent replacement of cylinders is required, since they are enough for one or two uses. Therefore, these pumps are widely used in cycling, when there are several seconds to pump up the wheel.
Pay attention to the recommended pressure, which is indicated on the bike tube and on the wheel tyre. The upper pressure limit is more suitable for driving on a flat paved road, the lower one is for rough terrain. By adhering to these recommendations, you will get the maximum pleasure from the ride, and extend the life of your bikes.
If your bike has an air suspension fork, you will need a high pressure pump to inflate it. It will pump very slowly if you try to pump the wheels with it. After all, such a pump is needed for other purposes.
The chamber in the shock absorber is very small, but requires high pressure to work properly. A conventional pump will not be able to provide the chamber with sufficient pressure, moreover, it will release everything that it has pumped up when it is disconnected from the nipple.
There are universal pumps, with a chamber that can change the volume, designed for both wheels and shock absorbers. But multifunctional things, as a rule, are worse than specialized ones.
January 26, 2022
The guys are friendly, doing everything seems to be good, there were no complaints! The price is certainly higher than others, those who are nearby.
December 30, 2021
Signed up in advance, waited 30 minutes until they started. So not the first time. They work well and quickly. Bolts are tightened by hand.
November 11, 2021
Well done guys, they know the job, prices are not bent, the best on the Donetsk highway, I recommend them only
October 27, 2021
Aww! The guy didn't know what to do at first.
Then I thought, took the wheel off my wheelchair, looked at the camera, patched and inflated the wheel. Prices are the lowest, pleased. Thank you!
02 September 2021
Fast, high quality, professional. Price as stated in advance by phone - nothing added. Everything is fine! Thank you!
January 01, 2021
The task was the following, to change the pieces of iron with tires in places to activate the tire pressure sensor. Thanks Dimitri, you did a great job!
September 13, 2020
Very qualified specialists, they clearly completed the work of repairing and straightening the wheels, they also cook discs and even repaired the metal high chair, like new, changing shoes was very fast and high-quality convenient, that they work around the clock, drove in at 22.30, I recommend to everyone, super tire service!
August 27, 2020
The best tire service. Alloy wheels are straightened, boiled with argon, metal wheels are rolled, side damage is repaired, and all this for quite normal prices compared to others, I advise everyone.
Any metals (copper, aluminum, stainless steel) are also boiled with argon.
02 February 2020
I have been changing tires here for the third year in a row, alloy wheels are repaired very efficiently and quickly.
I'm happy with everything. Recommend)
October 09, 2019
The only tire shop that is not afraid to inflate the wheels on an electric scooter. They also stuck an old camera on it for me. Excellent, I recommend it to everyone!
May 21, 2019
Excellent specialists, you can sign up in advance, come without a queue and service the car. I recommend
May 01, 2019
They didn’t cope with the motorcycle wheel, but they took money for 130 UAH, they were rude, maybe they change tires quickly, but there is a problem with vulcanization.
April 14, 2019
We made an appointment, arrived ten minutes early, and they began to serve us. There were two guys working. Changed shoes quickly, high quality. For four wheels paid 240 hryvnia.
