by Nicula Rose
Many parents do not take care of the stroller wheel whether it is fully air or not. The stroller can not be operated properly without full air filling in the wheel inner tube.
If you want to get the highest performance of a stroller then you must have to keep an eye on the wheels. Especially Before going out with a baby stroller, make sure that the air is full in the stroller wheel.
Today we will discuss in detail how to inflate bob stroller tires to get the optimum performance and some more discussion about the best pump and best tire in the market.
Page Contents
Don’t forget to bring some tools that will make your pumping experience awesome.
If you own a Bob stroller, chances are you will eventually need to inflate the tires. While this may seem like a daunting task, it is actually quite easy to do. With a few simple tools and a little bit of know-how, you can have your stroller’s tires inflated in no time.
The first thing you will need is an air compressor. You can find these at most hardware stores or online. Once you have your air compressor, attach the hose to the tire valve. Then, open the valve and start pumping air into the tire.
It is important to check the pressure frequently while inflating the tire. You can use a pressure gauge to do this. Once the tire is inflated to the desired pressure, close the valve and remove the hose.
That’s all there is to it! Inflating your Bob stroller’s tires is a quick and easy process that anyone can do.
The method of pumping is different due to different models of wheels. Below I will describe how to inflate the most popular tires in the present market.
First of all, remove the wheel from the stroller and open the valve stem cap from the valve stem tire. Follow the instruction (PSI limit) written on the wheel. Some tire PSI capacity is 235- 250 and some wheel capacity is more or less. It depends on the brand and model.
Now you can start pumping and check if is it okay or not. Never try to pump with a gas pump.
How to pump a bumbleride stroller wheelSome parents face trouble pumping up the stroller bumbleride wheel. Here is a solution for you. Check and make sure that the tire is properly seated with the rim, If not, adjust and re-align.
Now open the valve stem cap and pump till inflate up to 30 PSI. Standard PSI is 35 but we recommend 25. Be careful about overfilling.
Note: The best way to pump is foot and hand pump to 25-30 PSI.
How to pump up a bugaboo pram tireIt’s important to know the process of inflating a tube before the pump.
At first, unscrew the valve cap. Carefully attach or screw the pumper wheel valve and fill the air as required. If you inflate manually, follow the PSI up to 25-35. But the standard PSI is 30. After filling the air don’t forget to screw the valve cap.
Note: Please don’t use a gas pump to inflate the tube.
Final thoughtFinally, I am at the end of the detail explaining how to pump the bob stroller tire. Whether you try to inflate air in your stroller wheel, follow the process for better performance.
In case you don’t have a pump yet or are looking for an excellent quality pump then go through the Incredibly Useful Best Bob Stroller Inner Tube to pick the suitable one for you!
by Jenny Kim
In this article, we will go over how to put air in a stroller tire, and what you should be looking for so that you can do it without any trouble!
It’s one of the most common problems that parents have when they are out and about with their kids.
What was once an easy task has become more difficult because of all the new designs on strollers, but it is not impossible.
Steps on How To Put Air In A Stroller Tire
The first thing to do is put the pump nozzle right in between the handle and tire, then screw it on. You will need about 20 pumps for a regular-sized stroller tire, if you are using more than one of your hands then just count out loud!
The second step is to use an air compressor or have someone else help you by pumping while you guide. It can be difficult when doing this part alone so make sure that there is somebody around who can keep up with the workload for both ends of the hose.
Third step: Once full turn off valve (it should not take too many turns). If all went well there should now be enough pressure to open up those tires like a balloon.
Fourth step: Finish by inspecting the tires for any possible leaks or other concerns, then go on your merry way!
If you are using an air compressor make sure to use one that is designed specifically for this purpose such as those found at most stores like Walmart and Target.
Using these will allow you to fill up both of those tires with ease without worrying about hurting it in some way too much.
How do you pump a pram wheel?
Step 1. To pump a pram wheel, you first need to find the valve for it. In most cases, this will be on one of the back wheels (the ones that are not used when pushing from behind).
You can usually tell because there is an air hole in those tires where they enter into the rim and if you look closely at them, you might see some slight movement as well. The tire should also have its own side-specific cap with two or four holes to match up with each of your fingers.
Step 2. After locating both valves and caps then twist off whichever one does not correspond to what hand/fingers your using so it won’t get mixed up later. Now place your corresponding hands over the top of the valve, one hand on each side of the rim.
Step 3. Now pinch it by squeezing your hands together and rotate them in a circular motion until you feel some pressure from within the tire.
Step 4. Finally, release your grip and twist off the cap with either fingers or thumb to check if there is any air left inside (if so then close up that hole with whichever finger does not have an adjacent metal nail). Now repeat this process for the other wheel as well.
How are stroller tires measured?
Unlike in a car, the tires on your stroller can’t be measured using just one linear measurement. To find out what size of the tire is needed for your stroller, you will need two measurements: length and width.
As with any product that uses metric units or millimetres (mm) as its standard unit of measure, it’s important not to confuse these measures when ordering replacement parts for your stroller because they are different from inches or centimetres.
For example, if you want an 11 mm wide by 330 mm long tire then make sure you know how large those numbers mean before placing an order!
Now let’s talk about some common sizes found on many brands’ products today.
If I were to search for a tire on ikea.com, I would find that they offer tires in the following sizes: – 13 mm x 390 mm – 17mm x 430 mm – 25mm x 450 mm
How do you take a stroller tire off?
To remove the tire from your stroller, you will need to use a tool called a “spoke key” which is typically included with most bike kits. The spoke key comes in handy for tightening and loosening bicycle spokes but it can also be used on small screws found around the wheel of your stroller.
With this said, there are two places where you may find these screws: under the front or back wheels or near one of the rear legs/wheels. If those don’t work then try looking at any bolts that might connect metal
brackets like ones found hanging down between each leg (typically located just below where handlebars would be). These should pop right off once unscrewed with the right tool.
The thing to remember is that bicycle spokes are located in a straight line and airless tires have one wheelset higher than the other which would mean you’ll need to take off both of these screws before proceeding.
If your tire doesn’t seem very tight then use some sort of lubricants like WD40 or baby oil (which has an added benefit when it comes time for inflating).
The design of the devices is simple, but there are several types of pumps that differ in functionality, weight and appearance.
Electric pumps can only be operated when connected to the mains. Some models are battery operated. The advantage of such products is the minimum participation in the process of human work. In addition, the pumping itself takes place in a matter of seconds.
Leg Structures are easy to use as they only use one leg. They do not need electricity, and thanks to the simplicity of the products, even children can use them. With the help of a foot device, you can pump up not only the wheels of the stroller, but also the pool or mattress.
Water filter pumps are indispensable for inflating frame or inflatable pools. This type of product is not suitable for restoring pressure in the wheels of baby carriages. Therefore, when buying a pump, it is important to pay attention to its type and purpose.
A flat tire does not always mean that it is punctured.
Over time, even if the stroller is not used or the wheels are inflated irregularly, air comes out of the chamber (albeit slowly, but losses still occur).
Different wheels leak air at different speeds. Perhaps one wheel loosened faster than the others.
In this case, it is enough to pump it up and wait for a while. It takes 15-30 minutes to see that the air comes out very quickly and this indicates the presence of a puncture.
A punctured chamber must be sealed or replaced with a new one.
You can do it:
If you have the necessary tools and a pump; The technology for removing the tire from the rim and changing the tube is not much different between sidecars, bicycles and motorcycles. Therefore, strollers are easily accepted for repair in bike shops and tire services.
Under-inflated tires make driving difficult! Inflated tires make it difficult to ride and also increase the chance of a tire puncture.
It is necessary to inflate the wheels only with a hand pump, foot pumps are allowed, it is not recommended with compressors, if there is no way out, then carefully monitor the allowable pressure gauge readings!
Before inflating the wheels on the baby stroller, you should study the technical data sheet of the product. This document indicates the size of the tires and the allowable tire pressure. If this information is not in the technical passport or the document is lost, you can find the necessary information about the pressure indicators directly on the wheel tire. Very often, manufacturers place this information on the frame on stickers that indicate the permissible tire pressures.
The tire pressure is measured using a pressure gauge. If it is absent, it can also be detected manually by squeezing the spikes by pressing with a hand with little effort. Tire pressure for 8" to 14" tires will vary depending on where they are installed:
6 to 0.7 BAR; winter period - from 0.5 to 0.6 BAR; If the tire pressure is exceeded, the children's vehicle will move hard, which can lead to puncture, as well as spontaneous removal of the tire from the rim. Otherwise, with low tire pressure, the process of traffic will be difficult.
The process of inflating wheels is quite simple and does not require special technical knowledge, so you can do it yourself. The main requirement is the presence of a pump. Tires can be inflated without removing the wheel from the stroller:
Timely maintenance of children's vehicles will minimize the risk of making the necessary repairs at the wrong time. As for the chassis, you can also purchase special wheel covers for the baby stroller.
They will not affect the functioning of the transport itself in any way, but they will allow you to keep the apartment clean (in the case of storing transport in the corridor or on the balcony), as well as in the car trunk (during transportation).
If you have the experience of changing a bike tube and the necessary equipment, it will not be difficult to deal with a stroller wheel.
The following tools and equipment are required to change the inner tube yourself:
The sequence of actions would be:
So, alternately changing the blades, pull out one half of the tire. 
Pay attention to the rim. On the surface, where it comes into contact with the camera, there should be a protective tape called a “flipper”. This tape protects the camera from damage from the side of the rim. It may have burrs, scratches and joints. If there is no such tape, you need to wrap electrical tape on the rim or, in extreme cases, wide tape in several layers.
In this case no side vanes are required. To replace the camera you will need:
Both halves are attached to each other with 5 screws:
Insert the nipple into a special groove designed for it; Rims of this type are often rated at 1 bar. If you inflated more by mistake, then from excessive pressure the screws can be torn out of the plastic, the threads will break and the wheel will fall apart into two parts. If this happens, you need to pick up screws of a slightly larger size and length and screw them into the same holes. In plastic, they will roll a new thread and will firmly hold both halves together.
Inflation of wheels and replacement of the tube are not complicated procedures that require technical skills. Any man can quite master them. And this skill will come in handy later. After all, the child is growing. He will have a bicycle, which also needs technical care. You can contact any bicycle service, where those who wish will be happy to teach these simple operations.
Sources
[hide]
Good! We continue to test the Indigo stroller. We test it in difficult combat conditions. Namely: every day, no - several times a day I raise it to the second floor and lower it. On the stairs, sometimes loaded.
Yesterday in the park a wheel fell off near the stroller. Plus, it turned out to be lowered almost “to zero”. I don’t know how we didn’t notice right away… Tragedy! I mentally scolded the manufacturers of this stroller. I scrolled through my thoughts, how to walk now and what to do.
I took the wheel in an armful and went home with a three-wheeled stroller. (By the way, the stroller rode steadily and was stable).
The husband was not at home. And we had one more walk to go. How? How to walk without a stroller?! We are so used to it!.. The child was asleep. I decided not to sag and set to work. What can be difficult here? Just pump up the wheel and put it in place.
Pump up. If you did not have a bicycle as a child or had an older brother, then this task will seem incredibly difficult to you. I took the wheel, took the pump (bicycle), unscrewed the cap from the nipple, inserted the pump. I'm rocking. - Doesn't pump up. I thought I blew a tire. Since it won’t work to inflate, at least I’ll put the wheel back on.
Trying to put on. Falling off. There must be a release button somewhere. And she is not! Spin the wheel and set it aside.
Good. Google-there-everything. Thousands of articles. Thousands of tips. It turns out that this is the most common thing that breaks in wheelchairs.
I am a girl, and I need to explain everything in great detail and several times! I re-read, wasted time, but I did not find anything sensible. Everyone has different wheels and different opinions. Elementary, even to indicate to what pressure to pump the wheel, no one could answer. And, as it turns out, many glue tires without even removing them, as it is difficult.
I was upset... Well, OK, I found wheelchair repair shops on the Internet. (Kolaskoservice: tires, disks and other spare parts). I asked. - No one glues there, but they immediately change the camera (from 300 to 500 r) or the whole wheel (from 1500 to 2500). But there were no such workshops nearby, and it was not an option to go to them on three wheels ...
I had to look for men!) More precisely, not to look, but to call my brother, who always helps with such difficulties while her husband is working. He did everything in 5!! minutes! And I spent hours).
It turned out that the stroller did not break at all. The wheel flew off due to the fastening mechanism.
Namely: because of the small metal bracket.
Over time and from loads, it loosens, and (sometimes) rises. Like the spring mechanism in a clothespin. This must not be allowed. We need to keep an eye on this. So that it does not fly out, my brother secured it with an elastic band. Normal, for money)
The wheel was also intact. It's just that a bicycle pump requires screwing onto a nipple, otherwise air passes through. Therefore, it is better to use with a special nozzle or machine. As a rule, tires or chambers indicate to what pressure to inflate. But everything is checked for compression. Do not overdo it - if you pump over, the child will feel every bump.
Now about how to remove and put on the wheel on this model. Just. Press the bracket towards the center of the tire. The wheel comes off with no effort. Do you want to wear? - Again pressed the bracket. Inserted, released. All!
So the stroller adventures are over for now. We are walking again with our reliable friend Indigo.
