Toyota Tacoma Owners Manual / When trouble arises / Steps to take in an emergency / If you have a flat tire
Remove the flat tire and replace it with the spare provided.
■ Before jacking up the vehicle
● Stop the vehicle on a hard, flat surface.
● Set the parking brake.
● Shift the shift lever to P (automatic transmission) or R (manual transmission).
● Stop the engine.
● Turn on the emergency flashers.
■ Location of the spare tire
■ Location of the jack and tools
Regular Cab models
Access Cab models
Double Cab models
Taking out the jack and tool bag
Regular Cab models with bench type seat
Pull the lever and fold down the seatback.
Regular Cab models with separated type seat
Pull the lever and fold down the seatback.
Unhook the strap and remove the tool bag.
Loosen and remove the jack.
1. Loosen
2. Tighten
Access Cab models
1.Pull up the lever.
2.Raise the bottom cushion up.
Turn the knob counterclockwise.
1.Open the lid.
2. Press the lid against the bottom of the lower cushion until it is supported by the hookand- loop fastener.
Make sure that the lid is supported to prevent it from closing unexpectedly.
Unhook the strap and remove the tool bag.
Loosen and remove the jack.
1. Loosen
2. Tighten
Double Cab models
Swing the bottom cushion up by pulling the lock release strap.
1. Turn the knob counterclockwise.
2. Open the lid.
Unhook the strap and remove the tool bag.
Loosen and remove the jack.
1. Loosen
2. Tighten
Assemble the jack handle (in the tool bag)
Assemble the jack handle extension as shown.
Taking out the spare tire
Insert the end of the jack handle extension into the lowering screw and turn
it counterclockwise.
After the tire is lowered completely to the ground, remove the holding bracket.
Replacing a flat tire
Chock the tires.
Slightly loosen the wheel nuts (one turn).
Assemble the jack handle extension as shown.
Position the jack at the correct jack point as shown.
1. Front
2. Rear
Make sure the jack is positioned on a level and solid place.
Raise the vehicle until the tire is slightly raised off the ground.
When positioning the jack under the rear axle housing, make sure the groove on the top of the jack fits with the rear axle housing.
Remove all the wheel nuts and the tire.
When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.
Installing the tire
Remove any dirt or foreign matter from the wheel contact surface.
If foreign matter is on the wheel contact surface, the wheel nuts may loosen
while the vehicle is in motion, and the tire may come off the vehicle.
Install the tire and loosely tighten each wheel nut by hand by approximately the same amount.
Replacing a steel wheel with a steel wheel
Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.
Replacing an aluminum wheel with a steel wheel
Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.
Replacing an aluminum wheel with an aluminum wheel
Tighten the nuts until the washer of the nut comes into loose contact with the disc wheel.
Lower the vehicle.
Firmly tighten each nut two or three times in the order shown in the illustration.
Tightening torque: 83 ft·lbf (113 N·m, 11.5 kgf·m)
2WD models except PreRunner
4WD models and PreRunner
Stowing the flat tire, jack and all tool
Lay down the tire with the outer side facing up, and install the holding bracket.
4WD models only: Fasten the claws of the holding bracket into the wheel holes as shown in the illustration.
1. Holding bracket
2. Claw
Then secure the tire, taking care that the tire goes straight up without catching on any other part, to prevent it from flying forward during a collision or sudden braking.
Stow the tools and jack securely.
■After completing the tire change
The tire pressure warning system must be reset.
■When using the temporary spare tire
As the temporary spare tire is not equipped with the tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be warned. Also, if you replace the temporary spare tire after the tire pressure warning light comes on, the light remains on.
CAUTION
■Using the jack
Improper use of the jack may lead to death or serious injuries due to the vehicle
suddenly falling off the jack.
●Do not use the jack for any purpose other than replacing tires or installing and removing tire chains.
●Only use the jack that comes with this vehicle for replacing a flat tire.
Do not use it on other vehicles, and do not use other jacks for replacing tires on this vehicle.
●Always check that the jack is securely set to the jack point.
●Do not put any part of your body under the vehicle supported by a jack.
●Do not start or run the engine while your vehicle is supported by the jack.
●Do not raise the vehicle while someone is in it.
●When raising the vehicle, do not put an object on or under the jack.
●Do not raise the vehicle to a height greater than that required to replace the tire.
●Use a jack stand if it is necessary to get under the vehicle.
Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle will be injured.
■Using the jack handle
Tighten all the screws securely to prevent the extension parts from coming apart
unexpectedly.
■Replacing a flat tire
●Observe the following precautions.
Failure to do so may result in serious injury: • Lower the spare tire completely to the ground before removing it from under the vehicle.
• Do not try to remove the wheel ornament by hand. Take due care in handling the ornament to avoid unexpected personal injury.
CAUTION
■Replacing a flat tire
• Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc. may result in burns.
●Failure to follow these precautions could cause the wheel nuts to loosen and the tire to fall off, resulting in death or serious injury.
• Have the wheel nuts tightened with a torque wrench to 83 ft·lbf (113 N·m, 11.
5
kgf·m) as soon as possible after changing wheels.
• When installing a tire, only use wheel nuts that have been specifically designed for that wheel.
• If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer.
• Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
• When installing the wheel nuts, be sure to install them with the tapered ends facing inward.
■When using the temporary spare tire
●Remember that your temporary spare tire is specifically designed for use with your vehicle. Do not use your temporary spare tire on another vehicle.
●Do not use two temporary spare tires simultaneously.
●Replace the temporary spare tire with a standard tire as soon as possible.
●Avoid sudden acceleration, deceleration and braking, as well as sharp cornering.
CAUTION
■Speed limit when using the temporary spare tire
Do not drive at speeds in excess of 50 mph (80 km/h) when a temporary spare tire
is installed on the vehicle.
The temporary spare tire is not designed for driving at high speeds. Failing to observe this precaution may lead to an accident causing death or serious injury.
■Driving with tire chains and the temporary spare tire
Do not fit tire chains to the temporary spare tire.
Tire chains may damage the vehicle body and adversely affect driving performance.
■When the spare tire is attached
The vehicle speed may not be correctly detected, and the following systems may not operate correctly: ●ABS & Brake assist
●VSC
●TRAC
●Active traction control system (if equipped)
●Hill-start assist control system (if equipped)
●Downhill assist control system (if equipped)
●AUTO LSD system
●Cruise control (if equipped)
Also, not only can the following system not be utilized fully, it may actually negatively effect the drive-train components: ●4WD system
NOTICE
■Do not drive the vehicle with a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.
■When stowing the flat tire
Ensure that there is no object caught between the tire and the vehicle underbody.
■When replacing the tires
●When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly.
●Replace the grommets for the tire pressure warning valves and transmitters as well.
■To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants, the tire pressure warning valve
and transmitter may not operate properly. If a liquid sealant is used, contact your
Toyota dealer or other qualified service shop as soon as possible. Make sure to
replace the tire pressure warning valve and transmitter when replacing the tire.
Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the syst ...
If the engine still does not start after following the correct starting procedure (→P. 141) or releasing the steering lock (→P. 142), confirm the following points. ■ The engine wi ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple
suspected areas are listed, the potential causes of the symptoms are listed in order
of probability in the "Suspected Area" column of the table. Check each symptom by
check ...
Brake Switch "B" Circuit Short to Battery (P070312)
DESCRIPTION
The purpose of this circuit is to prevent the engine from stalling while driving
in lock-up when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then
the ECM cancels the operation of the lock-up clutch while braking is in p ...
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
...
Updated on Sep 27, 2022 · 3 min read
If disaster strikes and you need a spare tire for your
Toyota Tacoma
, you can find it underneath the truck bed, allowing you to get back on the road temporarily.
As the best-selling mid-size truck for the past 16 years, the Toyota Tacoma is affordable at a base price of just $26,700.
The Toyota Tacoma comes with a temporary spare tire, making it easy enough to replace the flat tire while you’re on the road.
Jerry
, the
car insurance
comparison
super app
, has put together this guide with answers to all your Toyota Tacoma spare tire questions! Keep reading for more information about the Toyota Tacoma temporary spare tire, including where to find it and how to replace a flat tire.
ZIP Code
ZIP Code
Find Savings!
No long forms. No spam calls. Free Quotes.
4.7/5 App Store Rating, 8,100+ Reviews
Trusted by 1.5+ Million Customers.
Is there a spare in a Toyota Tacoma?
Yes—Toyota Tacoma models come equipped with a temporary spare tire.
The temporary spare is identified with a “TEMPORARY USE ONLY” marking on the sidewall of the tire.
You can find your Toyota Tacoma spare tire stored securely under your truck’s bed.To access the spare, do the following (always check your owner’s manual to ensure you know how to perform each step):
Park your truck in a safe, level area as far away as possible from the flow of traffic
Use the tool kit provided to assemble the jack handle
Insert the end of the jack handle into the lowering screw where the spare tire is secured and turn it counterclockwise
Lower the spare tire to the ground
Remove the holding bracket from the spare tire
If the temporary spare is smaller and lighter than the regular tires, it shouldn’t be driven long distances or for long periods.
How to use the spare tire on a Toyota Tacoma
If you get a flat on your
Toyota
Tacoma, don’t panic! Remember to check your owner’s manual for detailed instructions before removing a flat tire and putting on the spare.
Maneuver carefully to the side of the road or, if possible, to a level area away from traffic, such as a parking lot.
Once safely away from the road, put the truck in park.
Use your hazards while your truck is pulled to the side of the road.
If possible, place wheel chocks in front of the front and rear wheels.
Lower the spare tire from under the truck using the jack handle.
Slightly loosen the wheel nuts on the flat tire by turning each one time.
Jack the truck up after placing the jack in the correct location.
Finish removing all the wheel nuts and the flat tire.
Slide the spare tire into place. Depending on the spare tire type, follow the instructions in your owner’s manual.
Lower the jack. Once the tire is on the ground, finish tightening the wheel nuts in a star pattern so that the tire is properly attached.
Drive to a mechanic or tire repair as soon as possible. Do not drive at high speeds or for long distances on the spare. The Toyota Tacoma’s temporary spare is only intended to get you to a nearby destination safely so you can get your truck tire repaired or replaced.
How to save money on car insurance for a Toyota Tacoma
A flat tire is more than an annoyance—it can get expensive fast. With the cost of one tire ranging from $150 to $350, imagine how pricey it could get if you have to replace all four!
The great news is that you now have options to help you save on car-related expenses! Let
Jerry
find you a new low rate on car insurance. Just download the Jerry app, answer a few short questions, and wait about 45 seconds while this licensed broker and the #1 rated insurance app searches 50+ top insurance companies to find you the lowest rates on the coverage you need.
Most users save an average of about $800+ a year! That’s more than enough savings to buy a full set of tires for your Toyota Tacoma!
“
Jerry
was easy to use, and they saved me a lot of money on my truck. I would definitely recommend them.” —Johannes T.
RECOMMENDED
No spam or unwanted phone calls · No long forms · No fees, ever
ZIP Code
ZIP Code
Find insurance savings (100% Free)
FAQs
How much is a Toyota Tacoma new tire?
A Toyota Tacoma replacement tire can run you between $150 and $350, depending on the manufacturer, the size of the tire, and where you purchase it.
Where is the spare tire on a Toyota Tacoma?
The spare tire on a Toyota Tacoma is under the truck’s bed.
How do you access the spare tire in a Toyota Tacoma?
To access the spare tire in a Toyota Tacoma, you need to crawl under the truck bed and use the tool kit provided to unlock and lower the spare tire.
Elizabeth is a word nerd who appreciates writing in all its forms, but she'd rather create an end-user manual than write in a reflective journal. With a bachelors in English, and masters in Teaching English as a Second Language, Elizabeth combines her love of words with all things technical. Her dream (and current) car is an Saab 9-3 Aero.
Published on Apr 27, 2022
Since the spare wheel is located under the floor of the car in a Land Cruiser, the owners of this car find it difficult when it is necessary to remove the spare wheel on a Land Cruiser 200 or 100. On most cars, it is located in the luggage hole , but in this Japanese it is located differently. Manufacturers have installed a separate design for lowering the spares of their brainchildren, the development of which causes problems.
Contents of the article:
To remove the spare wheel on a Toyota Land Cruiser 100, you need to do the following:
To install the removed spare wheel in the storage place, you need to do the described manipulations in reverse order.
For clarity, you can watch a video of the process of how to remove the spare tire on the Land Cruiser 200. It is not necessary to look for a video with a specific SUV model, since the device for lowering the spare tire is identical on TLK vehicles from 80 to 200.
The spare wheel lock is designed to prevent theft of the spare wheel. But it happens that the owner of the car cannot remove the spare tire on the Land Cruiser and needs to remove the protection. The reasons for this are:
The lock can be removed with a flat screwdriver. To do this, pry the pin with a screwdriver at such an angle that pressure is applied to it. Then use the tool as a lever and, with an effort, break out and remove the mechanism blocker.
As a preventive measure, the spare wheel mounting must be tested for serviceability.
To do this, you need to make sure that the mechanism for raising the spare wheel is working. Frequency - 1-2 times a year.
To prevent rust and protect against moisture, the winch is painted, disassembled and lubricated with special equipment. This allows you to remove the spare wheel on the Kruzak 200 at any time without hassle.
Oxidation of the spare wheel mounting mechanism is the cause of its failure. The emergence of a problem reveals the importance of prevention. But if a breakdown does occur, you need to know what means and measures to take to restore performance.
On car forums, Kruzak owners give several ways to get out of this situation:
Allegedly, the factory chain of this model does not lose its performance when contaminated. The solution to the nitrous problem is only a cleaning agent containing molybdenum.
In addition to removing rust, it forms a molybdenum film when applied, which protects the metal from moisture and re-corrosion.
Motorists explain the unusual location of the spare wheel in the TLC:
But with the advent of skill, removing the spare tire on the Land Cruiser 100 is not difficult. Toyota is an expensive and prestigious SUV that, like any car, needs care. Therefore, you should not save on consumables - cleaning and lubricants, as well as preventive maintenance. So the car will last a long time and will 100% justify its high price and reputation as a reliable vehicle.
| DIY
| ||
Toyota 4runner - Video Lesson Model: Toyota 4runner N280 - Years 2010-2022 In order to remove the spare tire from your vehicle, it is recommended that you leave the engine off so that you can safely complete all necessary steps. First go to the back of the car and lift the hood. Lower the seat to the leftmost position and immediately after that do the same with the small plastic door located according to the yellow notice. Inside are all the various tools needed to remove the spare wheel. Published 11 January 2022 by ScegliAuto | How to replace the rear wheel bearing Peugeot 407 How to intervene in the removal of the rear wheel bearing with all relevant parts on the Peugeot 407? We put the car on a column lift, loosen the pins with a telescopic wrench and raise it to a convenient height for intervention. We unscrew the pins and remove the rim, then we begin to unscrew the pins of the brake caliper by disconnecting it from the caliper, loosen the caliper pin with a socket wrench.  |
Take a straight pipe and insert it (at an angle) into the hole corresponding to the hood hook. Then take the L-shaped tube and attach it to the end of the previous tube. It remains only to turn counterclockwise so that the spare wheel is completely lowered. Unhook him from the security system and that's it. 
